REMS Power-Press SE Instrucciones De Servicio página 19

eng
If during closing of the pressing tongs, pressing tongs Mini or pressing rings a
marked ridge is created on the compression sleeve, the pressing may be
defective or not tight (see 5. Trouble).
CAUTION CAUTION
For preventing damages make sure to avoid operating situations like
exemplarily shown in Fig. 12 through 14, that no distortion between
pressing tongs, pressing tongs Mini, pressing rings, adapter tongs, adapter
tongs Mini, fi tting and drive unit occurs. Failure to do so could lead to
fracture and fl ying parts can cause serious injuries.
3.1.1. Working procedure 3.1.1. W 3.1.1. Working procedure
Press the pressing tongs, pressing tongs Mini (1) together manually until they
can be pushed over the press fi tting. Always position the drive unit with the
pressing tongs on the press fi tting at right angles to the pipe axis. Release the
pressing tongs so that they close around the press fi tting. Hold the drive unit
by the housing grip (6) and the pistol grip (9).
Place the pressing ring (20) around the pressing fi tting. Insert the adapter tongs/
Mini adapter tongs (19) into the drive unit and lock the tong retainer bolt, posi-
tion the rotary sleeve (27) if necessary, see 2.2. Insert the adapter tongs/Mini
adapter tongs (19) into the drive unit and lock the tongs retaining bolt. Press
the adapter tongs/Mini adapter tongs (19) together with your hand so that the
adapter tongs/Mini adapter tongs can be placed on the pressing ring. Release
the adapter tongs/Mini adapter tongs so that the radii/hemispheres of the adapter
tongs/Mini adapter tongs lie fi rmly on the cylinder rollers/ball sockets of the
pressing ring and the pressing ring on the press fi tting. With adapter tongs Z1
and Mini adapter tongs Z1, please note that the pressing ring may only be
applied below 45°.
On REMS Power-Press SE push the rotation direction lever (7) to the right
(feed) and press the safety inching switch (8). Keep the safety inching switch
(8) pressed until the pressing is fi nished and the pressing tongs or pressing
ring are closed. Release the safety inching switch immediately. Push the rota-
tion direction lever (7) to the left (return) and press the switch (8) until the press
rollers have moved back and the safety slip clutch responds. Release the safety
inching switch immediately.
NOTICE
Do not needlessly stress the safety slip clutch. Release the safety inching switch
immediately immediately after closing the pressing tongs, the pressing ring or moving back
the pressing rollers. The safety slip clutch is subject to normal wear like any
slip clutch. However, if it is needlessly stressed, it wears more quickly and can
be destroyed.
In the case of the REMS Power-Press and REMS Akku-Press, keep the safety
inching switch (8) pressed until the pressing is fi nished and the pressing tongs
or pressing ring is completely closed. This is indicated by an acoustic signal
(clicking). Press the reset button (13) until the press rollers (5) are fully retracted.
In the case of the REMS Mini-Press ACC, EMS Mini-Press ACC, REMS Mini-Press 22 V ACC, REMS
Mini-Press S 22 V ACC, Mini-Press S 22 V ACC, REMS Akku-Press ACC, REMS Power-Press ACC REMS Akku-Press ACC, REMS Power-Press ACC
and REMS Power-Press XL ACC, keep the safety inching switch (8) pressed
until the pressing is fi nished and the pressing tongs or pressing ring is completely
closed. After completion of press ing, the drive unit switches automati cally to
return (forced return). This is indicated by an acoustic signal (click).
Press the pressing tongs, pressing tongs Mini together with your hand so that
they can be removed from the pressfi tting together with the drive unit. Press
the adapter tongs, adapter tongs Mini together with your hand so that they can
be removed from the pressing ring together with the drive unit. Open the pressing
ring by hand so that it can be pulled off the pressfi tting.
3.1.2. Operating safety
On REMS Power-Press SE the pressing process is ended by releasing the
safety inching switch (8). A torque-dependent safety slip clutch acts in both end
positions of the press rollers for the mechanical safety of the drive unit. Do not
needlessly stress the safety slip clutch! REMS Power-Press SE is also equipped
with an electronic safety circuit which switches off the drive unit at high load.
As long as the pressing jaws (10), pressing rings (20) and pressing segments
(21) at "A" and "B" (Fig. 1, and Fig. 15 to 19) closed, this is not critical. However,
if the drive unit already switches off before pressing is complete (pressing jaws,
pressing rings and pressing segments at "A" and "B" not closed), work may not
be continued and the drive unit must be checked/repaired immediately by an
authorised REMS contract customer service workshop.
The REMS Power-Press and REMS Akku-Press ends the pressing opera tion
automatically, emitting an acoustic signal (clicking).
The REMS Mini- Press ACC, REMS Mini- Press ACC 22 V, REMS Mini- Press ACC, REMS Mini- Press ACC 22 V, REMS Mini-Press S
22 V ACC, REMS Akku-Press ACC, REMS Power-Press ACC and REMS 22 V ACC, REMS Akku-Press ACC, REMS Power-Press ACC and REMS
Power-Press XL ACC ends the pressing operation automatically, emitting an
acoustic signal (clicking), and returns automatically (forced movement).
NOTICE
A perfect pressing is only produced with full closure of the pressing tongs,
pressing tongs Mini, pressing ring or pressing segment. Full closure of
the pressing jaws (10), pressing rings (20) or pressing segment (21) both
at their tips (Fig. 1 and Fig. 15 to 19 at "A") and on the opposite side (Fig.
1 and Fig. 15 to 19 at "B") can be observed after completing the pressing.
If a visible burr is created on the pressing sleeve when closing the pressing
tongs, pressing tongs Mini, pressing ring or pressing segment, the pressing
may be faulty or leaking (see 5. Trouble).
REMS Mini-Press 22 V ACC, REMS
3.1.3. Working safety
To ensure safe working, the drive units are equipped with a safety inching switch
(8). This permits immediate switching off of the drive units at any time, particu-
larly if a potential hazard arises. The drive units can be switched to the return
function in any position.
3.2. Axial presses (Figs. 10, 11)
Note the different working range of the axial presses. The respectively latest
REMS sales literature applies, see also www.rems.de → Downloads → Product
Catalogues, Brochures. Make sure that the pressing heads (14) are inserted
into the drive unit in such a way that the pressing can be made in one stroke
if possible. This is not possible in some cases and pre-pressing and fi nish
pressing is necessary. For this, one pressing head or both pressing heads must
be inserted turned 180° before the second pressing process so that they are
closer together.
3.2.1. REMS Ax-Press 30 22 V(Fig. 11) 22 V 22 V(Fig. 11)
Place the preassembled compression sleeve fi tting inside the pressing heads
(14). Hold the drive unit by the housing grip (6) and the pistol grip (9), and keep
the safety inching switch (8) pressed until the compression sleeve is in contact
with the collar of the compression sleeve fi tting. This is also indicated by an
acoustic signal (clicking). Press the reset button (13) until the pressing heads
(14) are fully retracted. REMS Ax-Press 30: Upon completion of the pressing,
the drive unit switches over automatically to return (forced switch-off). This is
indicated by an acoustic signal (click). REMS Ax-Press 40: Hold the reset button
(13) until the pressing heads (14) have moved back completely.
If there is a noticeable gap between the compression sleeve and the collar of
the compression sleeve connector after closing the compression heads, the
pressing may be faulty or leaking (see 5. Faults). Read and observe the instal-
lation and assembly instructions of the manufacturer/supplier of the pressing
sleeve system to be pressed.
CAUTION CAUTION
Danger of cru shing! Keep your hands away from the moving pressing
heads (14)!
3.2.2. REMS Ax-Press 25 22 V ACC, REMS Ax-Press 25 L 22 V ACC (Fig. 10)
Insert the pre-assembled pressing sleeve fi tting into the pressing heads (14).
On the REMS Ax-Press 25 L ACC the closer distance of the pressing heads
may have to be achieved by moving the outer pressing head into the centre
pressing head position. Hold the drive machine either with one hand on the
switch handle (9) or two hands on the housing handle (6) and the switch handle
(9). Keep the safety inching switch (8) pressed until the compression sleeve is
touching the collar of the compression sleeve connector. The drive machine
then switches automatically to return (forced return).
If there is a noticeable gap between the compression sleeve and the collar of
the compression sleeve connector after closing the compression heads, the
pressing may be faulty or leaking (see 5. Faults). Read and observe the instal-
lation and assembly instructions of the manufacturer/supplier of the pressing
sleeve system to be pressed.
With the compression sleeve system IV, various pressing heads are needed
for one pipe size. Consult and comply with the instructions for installation and
fi tting of the system's manufacturer.
CAUTION CAUTION
Danger of cru shing! Keep your hands away from the moving pressing
heads (14)!
3.3. Pipe expanders
3.3.1. REMS Akku-Ex-Press 22 V ACC with expander Cu (Fig. 8)
Insert the expanding head into the pipe up to the stop and press the expanding
head/drive unit against the pipe. Switch on the drive unit. If the expanding head
is open, the drive unit switches automatically to return and the expanding head
is closed again. Read and observe the installation and assembly instructions
of the manufacturer/supplier of the used system.
3.3.2. REMS Akku-Ex-Press 22 V ACC with expander P (Fig. 8)
Push the compression sleeve over the pipe, insert the expanding head into the
pipe up to the stop and press the expanding head/drive unit against the pipe.
Switch on the drive unit (8). Make sure that the compression sleeve is far
enough away from the expanding head in the expanding process because
otherwise the expanding jaws (17) can bend or break. Keep the safety inching
switch (8) pressed until the pipe is expanded. This is indicated by an acoustic
signal (click). Expand several times if necessary. Turn the pipe slightly. Read
and observe the installation and assembly instructions of the manufacturer/
supplier of the used system.
3.3.3. REMS Akku-Ex-Press 22 V ACC with expander Q & E, REMS Power-Ex-Press
Q & E ACC (Fig. 8, 9)
Read and observe the installation and assembly instructions of the manufacturer/
supplier of the used system. Slide a Q & E ring of appropriate size onto the
pipe. Insert the expansion head into the pipe and press the expanding head/
drive unit against the pipe. Switch on the drive unit (8). When the expanding
head is opened, the drive unit switches automatically to return and the expanding
head is closed again. Keep holding the safety inching switch (8) down in the
REMS Akku-Ex-Press 22 V ACC and push the expanding head/drive unit further.
Turn the pipe slightly. Keep repeating the expansion process until the expanding
jaws (17) are slid all the way into the pipe. Release the safety inching switch
eng
19