Installation For Forward Facing Mode; For Child Between 9 -18Kg/Group; Forward Reclining Angle Adjustment; Shoulder Harness Height Adjustment - Joie tilt Manual De Instrucciones

5. Pull down the adjustment webbing and adjust it to the proper length to make sure your child is snugly
secured. 20
! Make sure the space between the child and the shoulder harness straps is about the thickness of
one hand.
Installation for Forward-Facing Mode
(for Child between 9-18kg/Group 1)
Reference age 1 - 4 years old
Seat position
Position 1 - Position 3: top red dot and bottom red dot aligned, as shown in
!
Please install the car seat on the vehicle seat first, and then place the child in the car seat.

Forward Reclining Angle Adjustment

While pushing the reclining adjustment handle 12
- 2
12 Angle indication: With a top red dot and the bottom red dot aligned.
The reclining positions are shown in 21 .
Proper Position of the Shoulder Harness Straps
Please choose the proper pair of shoulder harness strap slots according to the child's height.
! The shoulder harness strap slots should be at or slightly above the child's shoulder. Shoulder harness straps
that are too high or too low are not safe. 22
!
If the shoulder harness straps are not at the proper height, the child may be ejected from the car seat during a
crash.

Shoulder Harness Height Adjustment

Note
1. DO NOT remove the shoulder harness covers as they are important for preventing slippage of the
child during a collision.
2. Please thread the shoulder harness covers first, and then thread the shoulder harness straps
through shoulder harness covers.
3. During assembly, make sure the shoulder harness straps are not twisted.
4. Please reassemble the head support after assembling the shoulder harness straps.
5. DO NOT discard the back cover, for it must be assembled to the car seat before using in forward
facing mode.
6. Take off the head support and the small seat pad from the car seat before disassembling the
shoulder harness straps.
Disassembly of the Shoulder Harness
1. Pull up the webbing adjuster, while pulling the shoulder harness straps to the proper position.
- 1
8 Webbing adjuster
2. Remove the back cover from the body. 23
3. At the back of the seat, disassemble the two shoulder harnesses from the T-shaped steel plate.
17
21
- 1
, push the car seat to the desired position
4. Pull out the shoulder harness straps.
5. Thread the shoulder harness covers through the shoulder harness strap slots.
Assembly of the Shoulder Harness
1. Choose the proper shoulder harness slots and thread the shoulder harness covers through them.
!
Always ensure that shoulder harness covers are assembled with rubber side facing down towards
child.
2. Thread the shoulder harness straps through the shoulder harness covers.
!
To avoid the shoulder harness from getting twisted, please engage the buckle first.
3. Thread the shoulder harness straps through the shoulder harness slots.
4. Thread the two shoulder harness straps at the back of the seat onto the T-shaped steel plate.
The assembled shoulder harness straps are shown in
5. Thread the shoulder harness straps through the head support slot to fasten the head support to the
straps, and then pull the adjustment webbing tight.
6. Reassemble the back cover to the body.
Note
1. Please adjust the shoulder harness to proper height (at or slightly above the child's shoulder)
before installing the car seat. Please refer to
Shoulder Harness Straps Height
2. Please adjust the car seat to proper angle (3 possible positions for forward-facing mode). Angle
indication: With a top red dot and the bottom red dot aligned, as shown in
! Recline angle must be selected before car seat is installed in the vehicle. Adjusting the recline
position while car seat is installed in vehicle may loosen vehicle belts on car seat, leading to
serious injury or death in a crash.
3. When installing and adjusting the vehicle belts, make sure that both the shoulder belt and the waist
belt are not twisted and will not prevent the vehicle belts from functioning properly.
Forward-Facing Installation
1. Pull out the vehicle belt, rotate the car seat forward and thread the belt through the two forward-facing
vehicle waist belt slots at the back of the car seat shell.
2. Buckle the vehicle belt.
3. While pressing the car seat firmly into the vehicle seat, pull the vehicle shoulder belt toward the
retractor to fasten the car seat tightly and securely.
4. Open the lock-off device and insert the vehicle shoulder belt through it. Close the lock-off device onto
the vehicle shoulder belt.
!
Please check if car seat is installed tightly by moving the car seat back and forth at the vehicle belt
path. (Car seat should not move more than 25mm/1").
8
24
25
29
31
.
32
33
Proper Position of the Shoulder Harness Straps
Adjustment.
34
35
36
37
26
27
28
30
&
21
.
18