Proper Position Of The Shoulder Harness; Use Of Inner Cushions; Rearward Reclining Angle Adjustment; Rearward Facing Installation - Joie tilt Manual De Instrucciones

Proper Position of the Shoulder Harness Straps
Please choose the proper pair of shoulder harness slots according to the height of the child.
!
The shoulder harness slots should be at/or slightly below the child's shoulder. Shoulder harness straps that are
too high or too low are not safe. 5
!
If the shoulder harness straps are not at the proper height, the child may be ejected from the car seat during a
crash.

Use of Inner Cushions

Note
1. Inner cushions include head support and infant body support.
2. Head support is suitable for child in all installation modes.
3. Infant body support is for child's protection. A child 0-6 months must use infant body support.
1. Pull the head support aside and thread the shoulder harness straps through the head support slot to
fasten the head support onto shoulder harness straps.
Before assembling the head support, please check whether the shoulder harness straps are at the
proper height. Please refer to Proper Position of the Shoulder Harness Straps
Height Adjustment.
2. While pulling up on the webbing adjuster, pull out the shoulder harness straps to proper length.
- 1
8 Webbing adjuster
3. Press the red button to disengage the buckle
seat. 9
4. Engage the buckle until it clicks. 10
5. Pull the adjustment webbing tight. 11

Rearward Reclining Angle Adjustment

12
While pushing the reclining adjustment handle
- 2
reclined position. 12
Angle indication: The top blue diamond and bottom blue diamond are aligned (Position 4).
Note
1. Make sure the shoulder harness is adjusted to proper height before installing this car seat.
Please refer to Proper Position of the Shoulder Harness Straps
Adjustment.
2. First adjust the angle of the car seat to position 4. Angle indication: Align the top blue diamond and
bottom blue diamond. 4
3. When installing and adjusting the vehicle belts, make sure that both the shoulder belt and the waist
belt are not twisted and will not prevent the vehicle belts from functioning properly.
15
7
& Shoulder Harness
- 1
9 , and then place the infant body support in the car
- 1
, pull the car seat from the most upright position to the most
4
& Shoulder Harness Straps Height
Rearward-Facing Installation
1. Pull out the vehicle belt and engage the vehicle buckle tongue into the buckle.
- 1
13 Vehicle shoulder belt
- 2
13 Vehicle Waist belt
2. Rotate the car seat rearward and thread the vehicle waist belt through the two rear-facing vehicle
waist belt slots underneath the shell.
- 1
14 & 14
The correctly assembled belt is shown in
3. Install the vehicle shoulder belt in the two rear-facing vehicle shoulder belt slots at the back of the seat
shell. 16
!
Shoulder belt must pass through the rear-facing shoulder belt slots.
4. While pressing the car seat firmly into the vehicle seat, pull the vehicle shoulder belt to fasten the car
seat tightly and securely.
!
Please check if the car seat is installed tightly by moving the car seat back and forth at the vehicle
belt path (car seat should not move more than 25mm/1").
Correctly assembled vehicle belt is shown in
!
Waist belt pass through the rear-facing vehicle waist belt slots, as shown in
!
Shoulder belt must pass through the rear-facing vehicle shoulder belt slots, as shown in
!
The vehicle buckle tongue is engaged with the buckle correctly, as shown in
8

Securing your Child in the car seat

Note
1. Child 0 - 6 months must use the infant body support.
2. Please install the car seat on the vehicle seat first, and then place the child in the car seat.
3. After the child is placed in the seat, check whether the shoulder harness straps are at the proper
height. Please refer to
Height Adjustment.
1. Pull up the webbing adjuster, while pulling out the shoulder harness straps to the proper length.
- 1
8 Webbing adjuster
2. Press the red button to disengage the buckle
right sides of the car seat.
3. Place the child in the car seat and pass both arms through the harness straps.
!
After the child is seated, recheck whether the shoulder harness straps are at the proper height.
Please refer to
Adjustment
4. Engage the buckle until it clicks.
14
- 2
Vehicle belt slot
15 .
17
18 .
Proper Position of the Shoulder Harness Straps
- 1
9 , and then leave the harness straps on the left and
9
Proper Position of the Shoulder Harness Straps
5 .
10
13
- 1
18 .
- 2
18 .
- 3
18 .
& Shoulder Harness Straps
8
19
& Shoulder Harness Straps Height
16