Gwarancja I Serwis - GRAPHITE 58G491 Manual De Instrucciones

GWARANCJA I SERWIS

Warunki gwarancji oraz opis postepowania w przypadku reklamacji
zawarte są w załączonej Karcie Gwarancyjnej.
Serwis Centralny
GTX Service tel. +48 22 573 03 85
Ul. Pograniczna 2/4 fax. +48 22 573 03 83
02-285 Warszawa e-mail graphite@gtxservice.pl
Sieć Punktów Serwisowych
i pogwarancyjnych dostępna
gtxservice.pl
GRAPHITE zapewnia dostępność części zamiennych oraz materiałów
eksploatacyjnych dla urządzeń i elektronarzędzi. Pełna oferta części
i usług na gtxservice.pl.
Zeskanuj QR kod i wejdź na gtxservice.pl
do napraw gwarancyjnych
na platformie internetowej
TRANSLATION OF
THE ORIGINAL INSTRUCTIONS
CIRCULAR SAW
58G491
CAUTION: BEFORE USING THE POWER TOOL READ THIS MANUAL
CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
DETAILS OF OPERATIONAL SAFETY FOR CIRCULAR SAWS
WITHOUT RIVING KNIFE
CAUTION:
Neglecting the instructions specified in the below warnings about
risks and guidelines for safety of use may cause risks of electric
shock, fire and/or serious injuries.
DANGER
Keep your hands away from cutting area and cutting blade.
a.
Keep the second hand on the secondary handle or the motor
casing. When holding the saw with both hands the risk of injury with
cutting blade is reduced.
Do not reach under the processed material. Guard does not
b.
protect from rotating cutting blade below processed material.
Adjust cutting depth to thickness of processed material. It is
c.
recommended that the cutting blade reaches below the processed
material no more than tooth-length.
Never hold processed material in hands, never keep it on legs.
d.
Fix processed material to sound base. Good fixing of processed
material is important to avoid danger of contact with body, rotating
cutting blade being caught or loss of control over the operation.
When operating, hold the saw by insulated surfaces designed
e.
for such purpose.
Be very careful to avoid contact of the rotating blade with live
f.
wires or the power supply cord. Contact of power tool metal parts
with live wire may cause operator's electric shock.
For ripping cuts, always use guide for ripping or edge guide. It
g.
improves cutting accuracy and reduces risk of pinching the rotating
cutting blade in material.
Use only cutting blades with correct arbour hole diameter.
h.
Cutting blades that do not match seating may operate with eccentric
offset, which causes loss of control over operation.
Never use damaged or incorrect washers or bolts to install
i.
cutting blade. Washers and fixing bolts for cutting blade installation
were designed especially for circular saw to provide optimal
operation and safety of use.
Kick back, causes and ways to reduce it
• Kick back is a sudden lift and moving the saw back along the
cutting line towards the operator. This is caused by uncontrolled
cutting with cutting blade being caught, pinched or incorrectly
guided.
• When saw blade is caught or pinched in material, the blade stops
and motor reaction produces sudden movement of the saw to the
back, towards the operator.
• If the saw is unaligned or positioned incorrectly in the object
being cut, blade teeth may hit the upper surface of the material
when leaving the material. It will cause sudden raise of the saw,
and kick back towards the operator.
Kick back is an effect of improper use of circular saw, or wrong
operating procedures or conditions, and can be avoided by
observing applicable, below-mentioned precautions.
Hold the circular saw firmly with both hands in position that
a.
allows to resist kick-back. Stand to the side of the circular saw,
and not in the line of cutting. Kick back may cause sudden move of
circular saw to the back, but its force can be controlled by operator
when appropriate precaution measures are taken.
11