General Safety Information - Master Plumber 235817 Manual Del Usuario

Safety

General Safety Information

Your automatic sump pump should give years
of trouble-free service when correctly installed,
maintained, and used. However, interruption
of power to the pump, dirt/debris in the sump,
flooding that exceeds the pump' s capacity,
electrical or mechanical failure in the pump,
etc., may prevent normal pump operation. To
help prevent damage from flooding, purchase
a secondary AC sump pump, a DC backup
sump pump, and/or a high water alarm. See
Troubleshooting in this manual for information
about common sump pump problems and
remedies. For more information, call Master
Plumber customer service at 1-800-628-9439 or
visit our website at masterplumberpump.com.
Risk of electric shock. Can shock,
burn or kill. To reduce the risk of hazardous
or fatal electrical shock, follow instructions A
through D, below:
A. This pump has an approved 3-conductor
power cord with 3-prong, grounding-type plug.
Connect the pump only to a properly grounded,
3-prong outlet. If the sump pump circuit has
a 2-prong outlet, replace it with a grounded
3-prong outlet installed according to code.
B. Unplug the pump before handling or servicing
it. If your basement floor is wet, turn off all
power before walking on it. If the shut-off box
is in the basement, call your electric company
or hydro authority to shut off service to the
house, or call your local fire department for
instructions. After turning off the power,
remove the pump for service.
C. Protect the electrical cords from sharp objects,
hot surfaces, oil, and chemicals. Avoid kinking
the cords. Replace damaged or worn cords.
D. Do not lift the pump by the power cord.
Risk of fire. Plastic pipe glue
is extremely flammable. Follow the glue
manufacturer' s instructions when assembling
glued plastic pipe.
Risk of burns. Motors may run hot.
Allow 20 minutes to cool before handling.
1. Know the pump application, limitations, and
potential hazards.
2. Do not use this pump in water with fish
present. If any oil leaks out of the motor it can
kill fish.
3. Drain the system completely before servicing it.
4. To prevent a flexible discharge line from
whipping, which could cause injury or damage,
fasten it down before starting the pump.
5. Before each use, check any hoses in the
system for weakness or wear. Make certain that
all connections are tight.
For parts or assistance, call Master Plumber Customer Service at 1-800-628-9439
6. Periodically inspect the sump, the pump,
and the piping for debris and foreign objects.
Perform routine cleaning as required.
7. Personal Safety:
a. Wear safety glasses at all times when
working with pumps.
b. Keep your work area clean, uncluttered and
properly lighted; put away all unused tools
and equipment.
c. Keep visitors at a safe distance from the
work area.
d. Make workshop child-proof with padlocks
and master switches. Remove any
starter keys.
8. This pump installation must meet all applicable
laws, codes, and ordinances.
California Proposition 65 Warning
This product and related
accessories contain chemicals known to the
State of California to cause cancer, birth defects
or other reproductive harm.
Specifications
Power supply ................. 115V, 60 Hz, 15 Amp Circuit
Liquid Temp. Range ............... 32°F to 70°F(0°-21°C)
Individual Branch Circuit Required (min.).... 15 Amps
Discharge: .................................. 1-1/2" Female NPT
This pump is designed for use in a residential
sump only. Pump water only with this pump.
NOTICE: This unit is not designed as a waterfall
or fountain pump, or for applications involving
salt water or brine! Use with waterfalls,
fountains, salt water or brine will void warranty.
Do not use where water recirculates.
Not designed for use as a swimming pool drainer.
NOTICE: Read this owner' s manual for
installation, operation, and safety information.
Tools Required:
• Pipe wrench, Strap Wrench, or Slip-Joint Pliers
• Hacksaw
• Screwdriver
• File or Sandpaper
Materials Required:
1-1/2" ABS or PVC Pipe with Cement to match
Threaded Adapter (Pipe to Pump)
Check Valve – Purchase a FP0026-10 (goes in the
discharge line) or FP0026-6D (goes in the pump
discharge). If your check valve does not have an
1/8" anti-airlock hole, drill one in the discharge
pipe just above where it screws into the pump
discharge. Be sure to install the check valve so
that the flow will be away from the pump.
2