Technical Specifications; Layout And Components - FAAC 596 BPR Manual

1. WARNINGS
Before attempting any work on the electronic equipment
(connections, maintenance), always turn off power.
- Install, upstream of the system, a differential thermal breaker
with adequate tripping threshold.
- Always separate power cables from control and safety cables
(push-button, receiver, photocells, etc.). To avoid any electrical
disturbance, use separate sheaths or a screened cable (with
the screen earthed).
. TECHNICAL SPECIFICATIONS
Power supply voltage
Absorbed power
Motor max. load
Accessories max. current
Enviroment temperature
Fuses
Operating logics
Work time (time-out)
Pause time
Terminal board inputs
Terminal board outputs
Programmable functions
Functions through learning
3. LAYOUT AND COMPONENTS
J2
RADIO-DECODER
J2
Led
SW1
DL1
J3
OPTION
J7 OPEN
596
J7
615
OP-A CLOSE STOP SAFE FCA FCC
Led
- +
OPEN CL STOP
SAFE
J6 J9
J1
J6 J9
1
J1 IN/OUT FCA FCC
Description of components
J1 inputs terminal board and power supply to accessories
J2 connector for radio receiver (see Note)
J3 select operation: 596
J4 motor terminal board
JS 230 Vac power supply terminal board
J6 opening limit-switch connector (N.C. contact)
J7 OPEN command connector (for up-and-over)
J8 terminal-board for flashlight and courtesy light
J9 closing limit-switch connector (N.C. contact)
LED Signalling LEDs
SW1 programming key
TF1 transformer
F1 6.3A- 250 V (motor protection)
F2 self-resetting (accessories protection)
An RP2 type 2-channel receiver can be connected to the
J2 connector, so that the OPEN and CLOSE facilities of the
automated system can be commanded directly with a 2-
channel radio control.
If using a single-channel RP type receiver, only OPEN can be com-
manded.
CONTROL UNIT 596/615 BPR
230V~ - 50Hz
4 W
800 VA
250 mA
-20°C to +55°C
F1 = 6.3A-250V F2 = self-resetting
B/C, B, C, EP , AP , P , A default = EP
Self-learning (0-10 min in 2.5 sec steps)
Default = 10 min
Self-learning (0-5 min in 1.5 sec steps)
Default = 15 sec
Open, Close, Stop, Limit-switch,
CL safety devices, Power supply
motor, flashlight, courtesy light
and power supply to accessories
Operation for barrier or up-and-over
Logic
Work time, Pause time
F2
F1
J4
7
J8
10
230 Vac
J8
COM
J4
OP COM CL
or 615
4. CONNECTIONS
1
J1
IN/OUT
Description of terminal boards
Terminal Description
1 OPEN
2 CLOSE
3 STOP
4 - 24Vdc
5 + 24Vdc
TF1
6 SAFE
7
8 COm
9
10 LAmP
13
J5
11 COURT.
J5
L N
Fig. 1
12 COm
13 - 14 L - N
On boards supplied as a spare part or with operators on
which the limit-switches are optional items, the contacts of
connectors J6 and J9 are short circuited. If sensors are being
installed, eliminate the jumpers and connect the limit-switches
directly or via the specific adaptor, to the connectors. When the
travel-limit sensor is engaged, operation varies according to ope-
ration setting as 596 or 615 (J3).
Opening: immediate stop when sensor is engaged.
Closing: when the sensor is engaged, the operator works for 4 sec in
slow-down and for 1 sec. at standard speed (over-pushing stroke).
Opening and closing: when the sensor is engaged, slow-down is
executed with a duration of half the time at standard speed.
If the travel-limit sensors are not installed, the appliance executes
only the learnt work time (see par.6.).
4
7
10
J6 J9
FCA FCC OP COM CL
230 Vac
max 40W
M
230 Vac
max 60W
C
Other Safety
Devices
RX CL1 TX CL1
1
2
1
3
2
4
5
Device connected
Device with N.O. contact
(see chap. FUNCTION LOGICS)
Device with N.O. contact
(see chap. FUNCTION LOGICS)
Device with N.C. contact which cau-
ses the automated system to lock
Power supply for accessories
Closure safety device with N.C.
contact
(see chap. FUNCTION LOGICS)
motor opening stage
OP
motor common contact
motor closure stage
CL
Output for flashing light
230 Vac max 60W
Output for courtesy light 230
Vac max 40W
timing 90 sec. not modifiable
Common contact for light/flashing light
Board power supply (230Vac)
596
615
13
COM L N
230 Vac
+6% -10%
Fig. 2