Descargar Imprimir esta página

Makita DLS714 Manual De Instrucciones página 18

Sierra de inglete inalámbrica
Ocultar thumbs Ver también para DLS714:

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 99
1.
Make sure that the tool is switched off and the
battery cartridges are removed.
2.
Turn the hex socket bolt counterclockwise using
the supplied hex wrench with holding the center cover.
3.
Raise the blade guard and center cover.
4.
When cleaning is complete, return the center
cover and tighten the hex socket bolt by performing the
steps above in reverse.
WARNING:
Do not remove spring holding
blade guard. If guard becomes damaged in course
of time or UV light exposure, contact a Makita ser-
vice center for replacement. DO NOT DEFEAT OR
REMOVE GUARD.
Positioning kerf board
This tool is provided with the kerf boards in the turn
base to minimize tearing on the exit side of a cut. The
kerf boards are factory adjusted so that the saw blade
does not contact the kerf boards. Before use, adjust the
kerf boards as follows:
1.
Make sure to remove the battery cartridge. Then,
loosen all the screws (2 each on left and right) securing
the kerf boards.
► Fig.15: 1. Kerf board 2. Screw
2.
Re-tighten them only to the extent that the kerf
boards can still be easily moved by hand.
3.
Lower the handle fully and push in the stopper pin
to lock the handle in the lowered position.
4.
Loosen two clamp screws which secure the slide
poles.
► Fig.16: 1. Thumb screw
5.
Pull the carriage toward you fully.
6.
Adjust the kerf boards so that the kerf boards just
contact the sides of the blade teeth.
► Fig.17
► Fig.18: 1. Saw blade 2. Blade teeth 3. Kerf board
4. Left bevel cut 5. Straight cut
7.
Tighten the front screws (do not tighten firmly).
8.
Push the carriage toward the guide fence fully and
adjust the kerf boards so that the kerf boards just con-
tact the sides of blade teeth.
9.
Tighten the rear screws (do not tighten firmly).
10. After adjusting the kerf boards, release the stop-
per pin and raise the handle. Then tighten all the screws
securely.
NOTICE:
After setting the bevel angle ensure
that the kerf boards are adjusted properly. Correct
adjustment of the kerf boards helps to provide proper
support of the workpiece and minimizing workpiece
tear out.
Maintaining maximum cutting
capacity
This tool is factory adjusted to provide the maximum
cutting capacity for a 190 mm saw blade.
When installing a new circular saw blade, always check
the lower limit position of the circular saw blade, and if
necessary, adjust it as follows:
1.
Remove the battery cartridge. Then, push the car-
riage toward the guide fence fully and lower the handle
completely.
► Fig.19: 1. Adjusting bolt 2. Guide fence
2.
Use the hex wrench to turn the adjusting bolt until
the circular saw blade comes slightly below the cross
section of the guide fence and the top surface of the
turn base.
► Fig.20
3.
Rotate the blade by hand while holding the handle
all the way down to be sure that the circular saw blade
does not contact any part of the lower base. Re-adjust
slightly, if necessary.
WARNING:
blade and with the battery cartridge removed,
always be sure that the circular saw blade does
not contact any part of the lower base when the
handle is lowered completely. If a circular saw
blade makes contact with the base, it may cause
kickback and result in serious personal injury.
► Fig.21
Stopper arm
The lower limit position of the blade can be easily
adjusted with the stopper arm. To adjust it, move the
stopper arm in the direction of the arrow as shown in
the figure. Turn the adjusting screw and press down the
handle fully to check the result.
► Fig.22: 1. Adjusting screw 2. Stopper arm
Sub-fence
Country specific
CAUTION:
When performing left bevel cuts,
flip the sub-fence outward. Otherwise, it may con-
tact the blade or a part of the tool, and may result in
serious injury to the operator.
► Fig.23: 1. Sub-fence
This tool is equipped with the sub-fence. Usually posi-
tion the sub-fence inside. However, when performing
left bevel cuts, flip it outward.
18 ENGLISH
After installing a new circular saw

Publicidad

loading

Este manual también es adecuado para:

Dls714zDls714npt2Dls714nzDls714pt2