Remote Control - REVELL Control SAFARI 24069 Manual Del Usuario

3 CaMera

2 reMOTe COnTrOl

2A Power LED 3A ON/OFF button
2B ON/OFF button for 3B Charge socket /
the light USB port
2C Thrust control 3C Photo/video button
2D Control switch 3D Lens
2E Button for photo/video 3E LED
2F Left-right trim 3F MicroSD card slot
adjustment
3G Reset button
2G Direction regulator
5 ChargIng The helICOPTer
Attention: The battery and motor must cool down for 10 to 15 minutes before
charging and after every flight. Otherwise they can be damaged. The
charging process must be constantly monitored. Always ensure that the
charging process takes place on a fireproof surface in a fire-resistant
environment.
• Switch off the helicopter and the remote control (5A).
• Remove the connecting cable between the camera and the helicopter(5B).
• Carefully insert the charging cable in the charge socket of the helicopter(5C). The
plug must be gently inserted in the charge socket – DO NOT USE FORCE. If the plug is
not correctly inserted in the charge socket, the helicopter can be damaged and thus
may, under certain circumstances, entail a risk of injury.
• The charging process lasts approx. 110 minutes and must be continuously monitored.
• Disconnect the battery from the charging unit and disconnect the charging unit from
the outlet after the charging is completed.
The helicopter can fly for approx. 7-8 minutes after a charge time of approx.
110 minutes.
Warning notice: The LiPo battery heats up while charging. If it should become hot
and/or changes to the surface begin to appear, immediately discontinue the charging
process!
6 ChargIng The CaMera
• Switch off the helicopter and the remote control (6A).
• Remove the connecting cable between the camera and the helicopter.
• Carefully insert the charging cable in the charge socket of the camera (6B). The plug
must be gently inserted in the charge socket – DO NOT USE FORCE. If the plug is not
correctly inserted in the charge socket, the camera can be damaged and thus may, under
certain circumstances, entail a risk of injury. The LED on the camera will start to blink.
• The charging process is complete as soon as the LED is continuously illuminated. After
the charging process, disconnect the charging cable from the camera.
After a charge time of approx. 40 minutes, you can use the camera for approx.
20–30 minutes.
Note: If you are using the camera without the helicopter, switch it off before charging
– see below.
16
4 InserTIng BaTTerIes
(reMOTe COnTrOl)
4A Push down the clips on the
cover and pull back.
4B Insert 6 x 1.5 V AA batteries
and pay attention to the
polarity, as shown in the
battery compartment.
4C Close the battery compart-
ment cover.
7 sTarT PreParaTIOn
The thrust control (the left control on the remote control) must point down before
switching on (7A). Then set the control switch of the remote control to the "ON"
position; the Power LED will flash red (7B). Now move the thrust control to full throttle
and back to zero; the Status LED then illuminates continuously.
Set the ON/OFF switch on the side of the helicopter to the "ON" position (7C). Place
the helicopter on the ground so that the tail points toward you (7D). After a few
seconds the helicopter is ready to start.
8 usIng The CaMera
In-flight:
• Briefly press the video/photo button on the remote control to take a picture (the LED
will illuminate for a short while)
• Press the video/photo button on the remote control for about 3 seconds to record a
video (the LED will illuminate continuously) To stop recording, briefly press the button.
As a camera:
• Disconnect the cable from the camera.
• Push the retaining collar up and remove the camera from its holder (8A).
• Press the ON/OFF button on the camera for about 3 seconds; the LED will illuminate
and flash three times. The camera is now switched on.
• Briefly press the video/photo button on the camera to take a picture (the LED will
illuminate for a short while).
• Press the video/photo button on the camera for about 3 seconds to record a video
(the LED will illuminate continuously) To stop recording, briefly press the button.
• Press the ON/OFF button on the camera for about 3 seconds; the LED will briefly
illuminate and the camera is then switched off.
• To affix the camera to the helicopter, press the camera onto its holder and push it
back until the retaining collar clicks into place again (8B).
Downloading the data:
• Switch off the helicopter and the remote control. If you used the camera without the
helicopter, switch it off.
• Carefully insert the USB cable in the charge socket of the camera (6B). The plug must
be gently inserted in the charge socket – DO NOT USE FORCE.
• The LED on the camera will blink, the camera is recognised as a removable medium
and pictures and videos can be used.
Note:
• Before recording a flight, ensure that the connecting cable fits securely in the charge
sockets of the camera and helicopter.
• While the camera is connected to a USB port, it will be charged (which is why the
LED flashes).
• The camera may "crash". If it does, use a toothpick to press the reset button on the
side of the camera, next to the Micro SD slot.
• If the camera has not been used for 10 minutes, it automatically switches itself off.
17