Bevel Stop Adjustment - KNOVA KN M-3059R Manual Del Usuario

ADJUSTMENT
2. Place the blade (7) onto the arbor (9) and against the inner
blade collar (8). Then, place the outer blade collar (6) and
thread the arbor bolt (4) counterclockwise onto the arbor.
(Fig. O)
IMPORTANT: The flat side of the blade collars must be
placed against the blade. Do not install the collars with the
curved side against the blade.
3. Place the blade wrench on the arbor bolt (4).
4. Press the arbor lock button (5), holding it in firmly while
turning the blade wrench counterclockwise. Continue to
press it in while tightening the arbor bolt securely. (Fig. P)
5. Rotate the cover plate (3) back to its original position and
tighten the cover plate screw (2) with a Phillips screwdriver.
(Fig. O)
6. Lower the blade guard (1) back to its original position.
7. Pull the switch handle down and up several times to confirm
the lower blade guard operates without binding.
8. Be sure the arbor lock button (5) is released so the blade
turns freely. (Fig. P)
WARNING
•To avoid injury, never use the saw without
the cover plate secure in place. It keeps the arbor bolt
from falling out if it accidentally loosens, and helps
prevent the spinning blade from coming off the saw.
• If the cover plate is not secure in its proper place, the
guard may contact the spinning saw blade, resulting in
damage to the saw and severe personal injury.
• Make sure the collars are clean and properly arranged.
Lower the blade into the table and check for any contact
with the metal base or the saw table.
• ALWAYS MAKE DRY RUNS (UNPOWERED) BEFORE
FINISH CUTS SO THAT YOU CAN CHECK THE PATH
OF THE BLADE AND THE OPERATION OF THE GUARDS.
DO NOT CROSS HANDS.
REMOVING AND INSTALLING THE TABLE INSERT (FIG. R)
WARNING
To avoid injury:
• Always unplug the saw to avoid accidental starting.
Remove all small pieces of material from the table cavity
before performing any cuts. The table insert may be
removed for this purpose, but always reattach the table
insert prior to performing a cutting operation.
• Do not start the miter saw without checking for
interference between the blade and table insert. Damage
could result to the blade, table insert or turntable if
blade strike occurs during the cutting operation.
1. To remove, loosen and
remove the
six screws (1)
on the table
insert (2) with
a Phillips
screwdriver
and remove
the table
insert.
2. To install,
reposition the
table insert,
install the six
screws and
tighten.
1
2
Fig. R
13

BEVEL STOP ADJUSTMENT

WARNING
To avoid injury from an accidental start,
make sure the switch is in the OFF position and the
plug is not connected to the power source outlet.
90° (0°) Bevel Adjustment (Fig. S, T)
1. Loosen bevel lock handle (1) and tilt the cutting arm
completely to the right. Tighten the bevel lock handle (1).
NOTE: Make sure the detent block (2) touches the bevel
angle adjustment bolt (3). (Fig. S)
2. Place a combination square (4) on the miter table (5) with
the ruler against the table and heel of the square against
the saw blade. (Fig. T)
3. If the blade is not 90° square with the miter table, loosen
the bevel lock handle (1), tilt the cutting head to the left,
loosen the lock nut (6) and turn the bevel angle adjustment
bolt (3) in or out with an adjustable wrench until the blade
is square with the table. Once alignment is achieved,
tighten the lock nut (6) to secure the bolt (3). (Fig. S)
4. Tighten the bevel lock handle (1) after alignment is achieved.
6
3
2
Fig. T
WARNING
To avoid injury from an accidental start,
make sure the switch is in the OFF position and the
plug is not connected to the power source outlet.
90° Bevel Pointer Adjustment (Fig. U)
1. When the blade is exactly 90° (0°) to the table, loosen the
bevel indicator screw (1) using a Phillips screwdriver.
2. Adjust bevel pointer (2) to the "0" mark on the bevel scale
and retighten the screw (1).
Fig. S
1
5
4