Dimplex SP4 Serie Manual Del Usuario página 6

Manual Operation - SP420 & SP920
The switches are located at the bottom right side of the heater.
The Standby Switch (Switch S1) must be first turned 'ON' and the AUTO/MAN
(Switch S2) switch set to 'MANUAL' to operate the manual controls - see Fig.
6.
Note : When the fire is put in Manual mode the first time the flame effect will
come on indicated by the Bottom neon coming on for 3 seconds - see Fig. 7.
Manual Operation - SP520
The switches are located at the bottom right side of the heater
Remote Operation
The standby switch (S1) must first be turned 'ON' (and the 'AUTO/MAN' Switch
turned to 'AUTO' - SP420 & SP920).
Note: It takes some time for the receiver to respond to the transmitter. DO NOT
PRESS the buttons more than once within two seconds for correct operation.
Manual & Remote Operation
Setting Operation
Flame Effect only Press the ' I ' button (Switch 3)
Flame Effect & Heat On Press the ' I ' button again (Switch 3)
The Standby switch must first be turned 'ON' to operate the heater manually or
by remote control.
Note: It takes some time for the receiver to respond to the transmitter.
DO NOT PRESS the buttons more than once within two seconds for correct
operation.
To go to the previous settings press the O button.
Pressing the O button on the remote turns off the light & heat settings.
To resume press the I button until the desired setting is reached - see Fig. 8.
To increase or decrease the brightness of the flames, use the dimmer button or
the button on the Remote Control. The heat setting will remain the same.
To turn off the power the Standby Switch must be turned 'OFF'.
Lamp Replacement - SP420
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE
REMOVING LAMPS.
Warning - The lamps reach high temperatures during operation. For this
reason, allow the lamps to cool down after switching off the appliance.
The front panel will need to be removed in order to change lamps –see Fig. 9.
Warning - The front panel is heavy and easily damaged.
The front panel is fixed with 4 spring loaded pins (see 'z' in Fig. 9) and is
supported at the top by the chassis.
To gain access to lamps please apply the following procedure:
While holding the front panel by its sides with both hands, carefully pull forwards
the panel at the bottom until the pins detach from the clips - see Fig. 9.
When the bottom holding pins are undone, carefully pull forwards at the top
until the top pins detach and then lift the front panel up and out (see Fig. 9).
To gain access to the bulbs remove the screws at 'A' to remove the cover
bracket 'X' - see Fig. 9.
To gain access to the lamps, using a coin edge or screw driver turn catch ¼
turn anti-clock wise to unlock (see detail in Fig. 13). Open the hinged door (take
care not to lean or put weight on the door as this will result in damaging it)
Remove the defective lamp by unscrewing it (see Fig. 13).
Replace with a 60W E14 SES Clear candle bulb rotating it take care not to over
tighten the lamp.
Steps for reassembling the heater
Swing the door back in to position and turn the catch ¼ turn clock wise to lock
and replace bracket 'X' - see Fig. 9..
Replace the front by aligning the pins (see 'z' in Fig. 9) on the front frame with
the slots on the chassis and ensuring the pins engage fully in the slots.
Lamp Replacement – SP520 & SP920
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE
REMOVING LAMPS.
Warning - The lamps reach high temperatures during operation. For this
reason, allow the lamps to cool down after switching off the appliance.
The front panel will need to be removed in order to change lamps (SP520 see
Fig. 10) and (SP920 see Fig. 11).
Warning - The front panel is heavy and easily damaged.
The front panel is supported at the top by the chassis and held tight by
magnets at the top and bottom on the SP520 model - see Fig. 10. On the
SP920 the front panel is held at the bottom by a fixing screw - see Fig. 11.
SP520
To gain access to lamps please apply the following procedure:
While holding the front panel by its sides with both hands, carefully tilt the
bottom of the frame outwards until free and then lift the panel up (1) and then
All manuals and user guides at all-guides.com
- 2 -
- see Fig. 6.
Status
Top Neon
Bottom Neon
away (2) from the main body - see Fig. 10.
To gain access to the bulbs remove the screws at 'A' to remove the cover
bracket 'X' and the screws at 'B' to remove the cover bracket 'Y' - see Fig. 10.
For access to the bottom bulbs, carefully slide the flexible rotisserie (see 'a'
in Fig. 12) to one side ensuring that the rubber grommet is not lost (see 'b' in
Fig. 12).
Remove the defective lamp by unscrewing it (see Fig. 12).
Replace with a 60W E14 SES Clear Candle bulb, rotating it. Take care not to
over-tighten the lamp.
Steps for reassembling the heater
1. Refit the rotisserie making sure that the rubber grommet is carefully
pushed into the slotted hole on the axial bracket.
2. Replace the cover brackets 'X' and 'Y' - see Fig. 10.
3. Replace the front by aligning the slots on the front frame and making
sure that it catches fully on the support brackets.
The magnets on the chassis will hold the front flush to the main body.
SP920
To gain access to lamps please apply the following procedure:
Remove the fixing screw (1) from the base of the front frame while holding the
front panel by its sides with both hands, carefully tilt the bottom of the frame
out-wards until free and then lift the panel up (2) and then away (3) from the
main body – see Fig. 11.
To gain access to the bulbs remove the screws at 'A' to remove the cover
bracket 'X' - see Fig. 11.
To gain access to the lamps, using a coin edge or screw driver turn catch ¼
turn anti-clock wise to unlock (see detail in Fig. 13). Open the hinged door (take
care not to lean or put weight on the door as this will result in damaging it).
Remove the defective lamp by unscrewing it (see Fig. 13).
Replace with a 60W E14 SES Clear candle bulb rotating it take care not to over
tighten the lamp.
Steps for reassembling the heater
Swing the door back in to position and turn the catch ¼ turn clock wise to lock
and replace bracket 'X' - see Fig. 11.
Replace the front by aligning the slots on the front frame and making sure that
it catches fully on the support brackets and replace the fixing screw to the
underside of the front frame.
Cleaning
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE
CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use abrasive cleaners.
The glass viewing screen should be cleaned carefully with a soft cloth. DO
NOT use proprietary glass cleaners.
Recycling
For electrical products sold within the European Community.
At the end of the electrical products useful life it should not be
disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for recycling
advice in your country.
After Sales Service
Should you require after sales service or should you need to purchase any
spares, please contact the retailer from whom the appliance was purchased or
contact the service number relevant to your country on the warranty card.
Please do not return a faulty product to us in the first instance as this may
result in loss or damage and delay in providing you with a satisfactory service.
Please retain your receipt as proof of purchase.
UK