Installing And Removing The Battery Pack - Craftsman CMCE030 Manual De Instrucciones

CRAFTSMAN chargers, except the CMCB101, can be
stored on CRAFTSMAN VersaTrack™ Trackwall. Hooks and
accessories are sold separately. Please refer to the VersaTrack™
Trackwall accessory sheet for further information.
nOTE: The CMCB101 charger is not CRAFTSMAN VersaTrack™
Trackwall compatible.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Spindle Lock Button (Fig. A)

CAUTION: Turn tool off before changing accessories.
1. To lock the spindle 2 for changing accessories, press
and hold the spindle lock button
turning the spindle 2 until the spindle lock button
locks it in place.
2. To unlock the spindle 2 , release the spindle lock button
Changing Accessories (Fig. A)

WARNING: Ensure that the exposed mandrel length
is no more than .5" (13 mm) after inserting accessory
into collet.

WARNING: Use only accessories up to 1‑1/4" (32mm)
in diameter and rated at 34000 RPM or greater.

WARNING: Do not attach a toothed saw blade. Such
blades create frequent kickback and loss of control.
Reference these earlier sections for accessory related
information and precautions:
Additional Specific Safety Rules
•
Further Safety Instructions for All Operations
•
Additional Safety Instructions for Grinding
•
And Cutting‑Off Operations
• Additional Safety Instructions for Wire
Brushing Operations
Additional Safety Rules for Rotary Tools
•
Accessories are held in place by a collet
shown in Fig. A.
Several types of accessories mandrels may be used. See the
Accessories Chart.
nOTE: The screw, drum sander and felt mandrel accessories
should be assembled after the mandrels are installed into the
rotary tool.
standard mandrel
12 : Use with grinding wheels, grinding
stones, drill bits, wire brush wheels, cutters.
screw mandrel
13 : Use with cut‑off wheels and polishing
wheels. Place the washer between the accessory and
the screw.
sander mandrel 14 : Used with sanding drums. Push the
sanding drum over the mandrel and completly cover the
drum. If needed tighten the screw on the end of the mandrel
to expand the drum and secure the sanding drum in place.
Felt mandrel
polishing wheel onto the felt mandrel to secure in place.
To Insert an Accessory
1. Depress the ON/OFF button to turn tool off. Allow tool to
2. Remove the battery pack.
3. Press and hold the spindle lock button
4. Use the supplied wrench to turn the collet nut
5. Insert the accessory mandrel
6. Use the supplied wrench to turn the collet nut
1 while slowly
7. When finished, release the spindle lock button
1 .
Fixing Stuck Collets (Fig. H)
It is possible for a collet to get stuck within the collet nut
especially if a collet nut is tightened onto the tool without a
bit in place. If this happens, the collet can be removed from
the collet nut by pushing the shank of an accessory into the
hole in the collet nut. This should cause the collet to pop out
of the collet nut. Inspect collet for cracks.
OPERATION

Proper Hand Position (Fig. F)

3 and collet nut 4 as


Installing and Removing the Battery Pack

(Fig. E)

nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside the tool's base and slide it
into the base until the battery pack is firmly seated in the tool
and ensure that it does not disengage.
15 : Use with felt polishing wheels. Push the felt
come to a complete stop.
the collet nut 4 .
counterclockwise until it is loose.
collet 3 .
clockwise to tighten the collet nut
accessory mandrel.
nOTE: A wrench is provided with the tool, use only the
wrench provided. Do not use tools that could damage
the finish or break the collet. Always ensure there is an
accessory in the collet before tightening, tightening an
empty collet can damage it.
nOTE: If an accessory vibrates it can usually be corrected
by loosening the collet nut 4
as far as it will go, rotating it 1/4 turn and then retighten
the collet 3 .
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
5 into the tool base
English
1 and grasp
4
12 , 13 , 14 , 15 into the
4
4 securely onto the
1 .
, pushing the accessory in
16 , align the
11