Publicidad
Idiomas disponibles
Idiomas disponibles
Assembly and dismantling
the upper blower tube (03/3) is located in the
longitudinal groove (03/4).
2. Pull the lower blower tube (03/1) off the up-
per blower tube (03/3).
Removing the upper blower tube from the
appliance connection piece (04)
1. Slide the screwdriver (04/1) of the spark plug
spanner into the hole (04/2) of the locking
catch in the appliance connection piece until
the widest part of the screwdriver is under the
locking catch.
2. Turn the screwdriver by 90°; there must be
noticeable resistance. The locking catch re-
leases the upper blower tube (04/3). The
screwdriver remains inserted.
3. Pull out the upper blower tube (04/3).
4.3
Assembly for vacuum operation
Connecting the lower vacuum tube to the
upper vacuum tube (05)
1. Align the lower vacuum tube (05/1) to the up-
per vacuum tube (05/2) so that the two ar-
rows (05/3) and (05/4) face each other. The
following components face each other in this
position:
■
The cam (05/5) and the engaging
holes (05/6)
■
The groove (05/7) on the lower vacuum
tube and the cam (05/8) on the upper
vacuum tube
2. Slide both vacuum tubes firmly together until
the following occurs:
■
The cam (05/5) engages in the engaging
holes (05/6).
■
The upper vacuum tube impacts the limit-
ing ring (05/9) of the lower vacuum tube.
The two vacuum tubes are now firmly connected
together. They are not intended to be detached
from each other again.
Opening the intake grille of the appliance (06)
1. Hold the appliance (06/1) tight.
2. Firmly slide the screwdriver (06/2) of the
spark plug spanner into the upper lateral
opening (06/3) of the intake grille (06/4).
NOTE Do not slide the screwdriver into the
front lateral opening to which the arrow (that is
mounted on the vacuum grille) points.
3. Push the inserted screwdriver, together with
the intake grille, away from the appliance.
The intake grille swivels up.
2500043_d
Connecting the upper vacuum tube to the
appliance (07)
1. Hold the swivelled-up intake grille tight.
2. Align the upper vacuum tube (07/1) to the
housing opening (07/2) as follows:
■
The openings (07/3) of the transverse
grooves and the nubs of the housing
opening (07/4) face each other.
■
The vacuum tube is rotated so that the
two arrows (05/3) and (05/4) are at the
top.
3. Slide the upper vacuum tube (07/1) into the
housing opening (07/2) and rotate it firmly an-
ti-clockwise until it engages.
Connecting the exhaust air manifold to the
appliance connection piece (08)
1. Align the exhaust air manifold (08/1) to the
appliance connection piece (08/2) so that the
spring (08/3) and groove (08/4) face each
other. The two nubs (08/5) of the exhaust air
manifold must point downwards.
2. Slide the exhaust air manifold (08/1) into the
appliance connection piece (08/2) until it
sticks. The locking catch (08/6) does not en-
gage in the appliance connection piece.
Connecting the collecting sack to the exhaust
air manifold (09)
1. Open the hook and loop fastener (09/1) on
the blow-in opening (09/2) of the collecting
sack.
2. Slide the blow-in opening (09/2) of the col-
lecting sack over the blow-out connection
piece (09/3) of the exhaust air manifold until
the hook and loop fastener (09/1) is located
behind the bulge (09/4). The zip fastener and
carrying belt of the collecting sack must point
upwards.
3. Pull the hook and loop fastener (09/1) tight
and close it.
4. Pull on the collecting sack to check that it is
now firmly connected to the blow-out connec-
tion piece (09/3) of the exhaust air manifold.
5. Close the zip fastener of the collecting sack if
it is open.
Attaching the carrying belt to the collecting
sack (10)
1. Click the snap hooks (10/1) of the carrying
belt in the rings (10/2) on the collecting sack.
2. Pick up the appliance and hang the collecting
sack over your left shoulder. Adjust the
31
Publicidad
