Publicidad
safety precautions and usage statements
For optimal safety and operation, plug bed base into a surge protector (not included).
The bed base should only be plugged directly into a grounded wall outlet or surge
protector (strongly recommended). Improper connection of the equipment can result in
the risk of electrical shock, electrical file or faulty operation of this bed base. If the plug
does not fit your outlet, contact a qualified Electrician to install a suitable outlet.
IN-HOME USE AND HOSPITAL STANDARDS
Ergomotion adjustable bed bases are designed solely for in-home use. This base was not
designed as a hospital bed and is not designed to meet hospital standards. Do not use
this base with TENT TYPE oxygen therapy equipment or near explosive gases.
ADDITIONAL SAFETY FEATURES
Casters (optional leg accessory) are equipped with locking wheels to prevent
unwanted movement. Even when locked and unable to roll, it is possible for the
casters to slide. Free release head and foot motors are designed to lower the mattress
by retracting only with gravity, never pulling downwards, which minimizes pinch
points.
LIFTING/LOWERING MECHANISMS
The lift/lower feature will emit a minimal humming sound during operation. This is
normal. During operation, the lift arm wheels make contact with the platform support
of the base. This contact may result in metal on metal or metal on plastic contact.
This applies slight tension on the moving components and resonance is reduced to a
minimum level. If excessive noise or vibration is experienced, reverse the movement
action (up or down) of the base with the remote control. This should realign the
base's activating mechanisms to the proper operational position. In normal base
operation, the wheels, which allow the bed to maintain its distance from the wall, will
make contact with the steel platform supports of the base creating a contact noise.
When entering, exiting or shifting weight on the base, this contact noise may be
2
WARNING
ACOUSTICS
audible as the wheels make contact. This is normal.
MATERIALS
Ergomotion adjustable bases are constructed from various materials including woods,
metals, plastics and fabrics. Tension, pressure or movement applied to the frame,
platform or shroud through general use may create an audible sound.
TOLERANCE
All Ergomotion adjustable foundations, depending on make and model, are designed
and manufactured to perform and function within designated quality control
parameters. Bases are subject to meticulous and rigorous inspections during the
All Ergomotion adjustable foundations, depending on make and model, are designed and manufactured to perform and
function within designated quality control parameters. Bases are subject to meticulous and rigorous inspections during
quality control process to ensure bases will operate within these standards during
the quality control process to ensure bases will operate within these standards during normal operating use.
Normal operating use is defined as the following:
-Adjustable foundation is to be operated with a mattress and load. Testing procedures require lifetime cycle
tests with up to 120kg distributed load.
The angle (designated "α" in figure 1) between the back section and the flat section for various configurations of the
mattress support platform shall be ± 3°, which translates to a tolerance of up to 1 ½".
normal operating use. Normal operating use is defined as the following: Adjustable
The angle (designated "β" in figure 1) between the flat section and foot section for various configurations of the mattress
support platform shall be ± 3°, which translates to a tolerance of up to ¾".
foundation is to be operated with a mattress and load. Testing procedures require
When operating a "paired" split base setup there may be a time latency up to 1.5 seconds between each bases articulation.
Any adjustable foundation deemed to be within these allocated tolerances is considered to have met the manufacturer's
lifetime cycle tests with up to 120 kg distributed load. The angle (designated "a" in
quality control standards.
Blake Pettit
figure 1) between the back section and the flat section for various configurations of
Quality Assurance Manager
Ph 805-979-3875
the mattress support platform shall be ± 3°, which translates to a tolerance of up to 1
Fx 805-979-9399
www.ergomotion.com
½".
Ergomotion Inc.
|
ph 1-888-550-3746
|
fx 805-979-9399
The angle (designated "b" in figure 1) between the flat section and foot section for
various configurations of the mattress support platform shall be ± 3°, which translates
to a tolerance of up to ¾".
Adjustable
Bed Tolerance
(α°)
(β°)
|
www.ergomotion.com
Publicidad
