Trixie TX6 Manual De Instrucciones página 4

G
Instructions
Please read the instructions fully before you start opera-
ting the device.
Installing batteries:
1. Unlock the cover with the release knob and lift it off.
The battery compartments are on the underside of the
cover.
2. Remove the battery covers and install four new Alkaline
batteries Baby C.
3. Replace the battery covers. Make sure that the covers
snaps securely into place.
4. Turn device off again if it starts automatically.
5. Press and hold down the buttons indicated below for
3 seconds:
6. Place the device securely on even ground.
Turning the device on:
1. Open the cover of the control panel and switch the device
on or off with the ON/OFF button (the round button on
the left).
2. When the device is switched on, the time will automati-
cally flash at '12:00 A.M.'.
3. Every time a button is pressed, the automatic food
dispenser confirms this with a beep. First press the ENTER
button to set the current time. The hour flashes.
4. Use the arrow buttons to set the hour. During setting,
the time changes automatically between A.M. (morning
to noon) and P.M. (afternoon to midnight).
5. After you press ENTER again, the minutes start flashing.
6. Use the arrow buttons to set the minutes.
7. When the time is correct, end the setting process by
pressing ENTER.
Choosing the meal:
1. Keep ENTER pressed for 3 seconds. Now MEALS begins to
flash, and you are in the meal setting mode. Press ENTER
again and BREAKFAST flashes.
2. Use the arrow buttons to choose the meal that you want
to programme. BREAKFAST, LUNCH and DINNER will
flash one after the other when the arrow buttons are
pressed.
4
3. Press ENTER when you have chosen the meal you want.
a. Then YES will flash. Now press ENTER if you want to set
the time for the meal.
b. If you do not want to set the time for this meal, use the
downward arrow to choose NO and then press enter.
Please note: If NO is chosen, the software will go back to
MEALS. Use the arrow buttons to choose the meal that
you want to programme.
Feeding times:
After you have chosen the MEAL and selected YES, the
hour flashes.
1. Use the arrow buttons to set the hour for the meal.
2. Please note: during setting, the time changes automati-
cally between A.M. and P.M.
3. Press ENTER again and the minutes start to flash.
4. Use the arrow buttons to set the minutes for the meal.
5. Press ENTER when the minutes have been set. The menu
then automatically continues to setting the meal size
(BOX).
Setting meal size:
After you have set the feeding time, the menu for setting
the meal size flashes (on the right on the display).
1.Set the meal size that is to be served with the arrow
buttons. For each meal, you can choose 1, 2 or 3 BOX
(food units). One food unit is one of the six cavities in the
device (approx. 240 ml or 1 US cup each). If you choose
two or three food units for a meal, the cavities will open
one after the other with an interval of 10 minutes.
2. Press ENTER to end the setting.
Setting other meals:
Repeat the programming as described above for each
meal. After you have programmed all meals, press ENTER
until the device beeps twice. That means your settings are
confirmed.
Important:
• The counter SERVED shows how many food units have
been served. Once all 6 food units have been served, the
red LED light flashes slowly and new food has to be filled
in. After filling the device, press START and the device will
work according to the programming. The counter goes
back to zero.
• After programming, make sure that the cover over the
control panel is securely fastened so that your pet cannot
change the settings by accident.
Extra option manual feeding: Keep the down arrow
pressed for 3 seconds. This releases one food cavity
immediately.
Information:
• The following feeding times are preset: breakfast at 6:00
A.M., lunch at 12:00 P.M. and dinner at 6:00 P.M.