Denon AVR-1602 Instrucciones De Operación página 14

ENGLISH
[2] Listening over headphones
1 Connect the headphones to the
PHONES jack of the front panel.
2
Press the SPEAKER A or B
button turn the speaker off.
CAUTION: No sound is produced from the headphones
when speakers A or B are turned on.
[3] Turning the sound off temporarily (muting)
1 Use this to turn off the audio output
temporarily.
Press the MUTING button.
Cancelling MUTING mode.
Press the MUTING button again.
Muting will also be cancelled
when MASTER VOL is adjusted
up or down.
[4] Combining the currently playing sound with the desired image
1 Simulcast playback
Use this switch to monitor a video
source other than the audio source.
Press the VIDEO SELECT button
repeatedly until the desired source
appears on the display.
Cancelling simulcast playback.
• Select "SOURCE" using the VIDEO SELECT
button.
• Switch the program source to the component
connected to the video input.
[5] Checking the currently playing program source, etc.
1 Front panel display
• Descriptions of the unit's operations
are also displayed on the front panel
display. In addition, the display can
be switched to check the unit's
operating status while playing a
source by pressing the STATUS
button.
14
All manuals and user guides at all-guides.com
NOTE:
To prevent hearing loss, do not raise the volume level
PHONES
excessively when using headphones.
B
1
2
(Main unit)
MUTING
SYSTEM SURROUND
SET UP MENU MASTER
CH SELECT VOL
SELECT
T.TONE STATUS MUTING
(Remote
RETURN DISPLAY
control unit)
VIDEO SELECT
3 2 0
(Remote
VIDEO SELECT CD·MD/CDR·DVD/VDP DISC SKIP+
1
control unit)
TITLE
8 3 9
2
6 7
STATUS
SET UP MENU
MASTER
CH SELECT VOL
DISPLAY
SELECT
T.TONE STATUS MUTING
RETURN DISPLAY
(Remote
CHANNEL TV VOLUME
control unit)
Playback using the external input (EXT. IN) jacks
1 Set the external input (EXT.
IN) mode.
Press the EXT. IN button to
switch the external input.
Once this is selected, the
input signals connected to
the FL (front left), FR (front right), C (center), SL
(surround left) and SR (surround right) channels
of the EXT. IN jacks are output directly to the
front (left and right), center, surround (left and
right) speaker systems without passing through
the surround circuitry.
In addition, the signal input to the SW (subwoofer)
jack is output to the PRE OUT SUBWOOFER jack.
2
Cancelling the external input mode
To cancel the external input (EXT. IN) setting,
press the INPUT MODE (AUTO, PCM, DTS) or
ANALOG button to switch to the desired input
mode. (See page 13.)
1
(Main unit)
• When the input mode is set to the external input
(EXT. IN), the play mode (STEREO, DOLBY/DTS
SURROUND, 5CH STEREO or DSP SIMULATION)
cannot be set.
Recording the program source (recording the source currently being monitored)
1 Follow step 1 to 3 under "Playing the input source".
Simultaneous recording
The signals of the source selected with the function selector button are output simultaneously to the
CDR/TAPE and VCR REC OUT jacks. If a total of two tape and/or video decks are connected and set to the
recording mode, the same source can be recorded simultaneously on every decks.
NOTES:
• The AUDIO IN's signal selected with the function selector button are output to the CDR/TAPE and VCR
AUDIO OUT jacks.
• The DIGITAL IN's signal selected with the function selector button are output to the DIGITAL OUT (OPTICAL)
jack.
1
8
B
(Main unit)
(Remote
control unit)
2 1
V. AUX
4
1, 2 INPUT MODE CDR / TAPE
8
SURROUND
MODE
NOTES:
8
• In play modes other than the external input mode,
the signals connected to these jacks cannot be
played. In addition, signals cannot be output from
(Remote control unit)
channels not connected to the input jacks.
• The external input mode can be set for any input
source. To watch video while listening to sound,
select the input source to which the video signal
is connected, then set this mode.
2 Start recording on the tape or video deck.
For instructions, refer to the component's operating
instructions.
VCR TV/DBS
5 6 7
TUNER SHIFT
9 0
·
TAPE VCR
6 7
CHANNEL