Publicidad
Idiomas disponibles
Idiomas disponibles
EN
- If your socket outlet is not suitable for the plug, then
the plug must be removed (cut off if it is a mould-
ed on plug), the flexible cord insulation should be
stripped back as appropriate and a suitable 3 pin
plug fitted.
• WARNING: Dispose of a plug that has been cut from
the power supply cord, as such a plug is hazardous
if inserted in a live 13A socket outlet elsewhere in
the house. - Should the fuse need to be replaced
an ASTA marked fuse, approved to BS1362, of the
same rating must be used. - Always replace the fuse
cover after fitting a fuse. The plug must NOT be used
if the cover is omitted or lost until a replacement is
obtained. - Make certain that only the correct fuse
cover is used and fitted. - For plugs with detachable
fuse cover the replacement must be the same as the
colour insert in the base of the plug, or as directed by
the embossed wording on the base of the plug. - If
the detachable fuse cover is lost a replacement may
be purchased from a Service Centre.
T.S.
( if fitted)
NOTE: (Automatic Stop System), which stops the
machine during the bypass phase. To start the water
cleaner, it is therefore necessary to set the switch on
position (I)"ON"; after that press the pistol trigger:
the Automatic Stop System will start the machine
and will stop it automatically when the trigger is
released. It is advisable to put on the safety of the
pistol trigger whenever the machine is stopped, in
order to avoid unintentional starting.
· Any automatic start of the machine without press-
ing the gun trigger is attributable to air bubbles in
the water or other similar phenomena which do not
imply the existence of any defects in the machine.
· Do not leave the appliance unattended during the
standby for more than 5 minutes. Contrarily, for the
safety of the appliance it is necessary to re-turn the
switch into the (0) OFF position.
· Please check that the coupling of the high pressure
hose with the appliance and the gun supplied as
standard equipments made correctly, that is to say
without any water leak.
> SWITCHING OFF
See fig.
turn the switch pos. 2 (0) OFF position and wait that
the water get completly cold.
In this way you avoid any calcareous deposit and
overheatings of the coil and the boiler, which are
20
always dangerous.
IMPORTANT: When the machine is switched off,
always discharge the pressure hose, opening the
gun.
CARE AND MAINTENANCE
See fig.
X X WARNING: the machine shall be discon-
•
nected from its power source, by removing
the plug from the socket-outlet, during
cleaning or maintenance
• WARNING: Do not spray the appliance with
water and do not use detergents or aggres-
sive solvents. Machine could be damaged.
·
Clean the exterior part of the machine with a dry
cloth.
- Always keep the machine clean so that the cooling
air can pass through the slits without obstructions..
- Cleaning the water filter: To ensure the pump gives
good service it is extremely important to check and
clean the water filter frequently. Use pliers to extract
it from the pump and rinse it carefully in running wa-
ter.
- Cleaning the nozzle: A blockage in the nozzle may
prevent the machine from operating correctly, so it
must be kept clean. Switch off the machine and re-
move the lance. Clean the nozzle with the pin pro-
vided. Rinse the lance in running water.
- When topping up the oil in the pump, use a SAE
20W40 mineral oil. Quantity supplied: 70 gr.
- The replacement of the fuel metal pipe is requested
after disassembling to avoid fuel leakages.
> STORAGE
See fig.
· Move the machine only by grasping the car-
rying handle
· Store the appliance and the accessories in a
frost-safe room.
WARRANTY CONDITIONS
All our machines are subjected to strict tests
and are covered against manufacturing de-
fects in accordance with applicable regula-
tions. The warranty is effective from the date of
purchase. The following are not included in
the warranty: - Parts subject to normal wear.
- Rubber parts, charcoal, filters and the ac-
cessories and optional accessories. - Acciden-
tal damage, caused by transport, neglect or
inadequate treatment, incorrect or improper
use and installation failing - The warranty shall
Publicidad
