Mounting Surface - ETI 56574142 Guía De Uso Y Cuidado

SURFACE MOUNTING
With power disconnected to the electrical box, remove the existing fixture. Make a sketch of how the
current fixture is wired (by wire color or mark the wires with masking tape and a pencil so you will
know how to properly reconnect the wires to the new LED light fixture. Also,open one side of the end
cap by screwing off the two screws, remove the waterproof connector and linking cable of the new
fixture before the surface mounting.
Installing the U brackets：
1
• Hold the U brackets (D) up to the mounting surface to determine the mounting position.
NOTE: The U brackets (D) should be positioned 33 inches apart.
• Mark the screw positions for the U brackets (D) on the mounting surface.
• Drill two 1/8 in. pilot holes into the screw locations marked on the ceiling. You can also use an
awl or nail to dimple the screw holes.
• Install a drywall anchor (C) in each drilled mounting hole.
• Insert two mounting screws (B) through the U bracket (D) and into the drywall anchors (C) installed
in the mounting surface.
• Tighten each mounting screw (B) to secure the U bracket (D) to the mounting surface.
• Repeat the installation for the second U bracket (D).
Completing the installation
2
• Snap the fixture body into the U brackets (D) installed on the

mounting surface..

• Feed the electrical connection wires through the open hole of the
end cap.
• Connect the hot and neutral (black and white) wires from the
fixture body to the same color wires from the electrical box using
the wirenuts.
• Connect the green wire from the fixture body to the grounding
wire from the electrical box using the wirenuts.
• Wrap the wirenuts with electrical tape for a more secure
connection.
• Screw up the end cap and restore the power supply to turn on
the light.
CONTINUOUS SURFACE MOUNTING
The continuous mounting steps are based on the surface mounting and continuous suspended installation.
NOTE: Multiple light fixture can be connected, up to a maximum of 8 lights.
WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire,
or other injuries which could be hazardous or even fatal. • Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker. •
SUITABLE FOR OPERATION IN AMBIENT NOT EXCEEDING 45°C. SUITABLE FOR WET LOCATIONS. MINIMUM 90°C SUPPLY CONDUCTORS. CAUTION-RISK OF SHOCK. DISCONNECT POWER
BEFORE SERVICING.
NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which
the receiver is connected, and consult the dealer or an experienced radio/TV.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
Patent No. 10,352,510
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754) www.ETiSSL.com
mounting surface
C
D
B