Descargar Imprimir esta página

Infiniton FGC-210B Manual De Instrucciones página 35

Publicidad

Idiomas disponibles

Idiomas disponibles

Unobstructed ventilation shall be maintained around the appliance or in an embedded structure.
Preparations for use
5.
Standing time
After the refrigerator is properly installed and well cleaned, do not switch it on immediately. Make sure to energize the
refrigerator after more than 1 hour of standing, so as to ensure its normal operation.
6.
Cleaning
Confirm the accessory parts inside the refrigerator and wipe the inside with a soft cloth.
7.
Power-on
Insert the plug into the solid socket to start the compressor. After 1 hour, open the freezer door, if the temperature inside
the freezer compartment drops obviously, it indicates the refrigeration system is working normally.
8.
Storage of food
After the refrigerator runs for a period of time, the internal temperature of the refrigerator will be automatically controlled
according to the user's temperature setting. After the refrigerator is fully cooled, put in foods, which usually need 2~3 hours
to be fully cooled. In summer, when the temperature is high, it takes more than 4 hours for the foods to be fully cooled (Try
to open the refrigerator door as less as possible before the internal temperature cools down).
If the refrigerator is installed in the moisture place, make sure to check whether the ground wire and leakage circuit
breaker are normal. If vibration noises are produced due to the refrigerator contacting the wall or if the wall gets blackened
by air convection around the compressor, move the refrigerator away from the wall. Setting up the refrigerator may cause
jamming noise or image chaos to the mobile phone, fixed-line telephone, radio receiver, television set surrounding it, so
try to keep the refrigerator as far away as possible in such case.
III.
Functions
The display panel is designed on the fridge door, the pattern of which is displayed as the right Figure.
When the refrigerator system is connected to power supply for the first time, all icons on the display panel gets
illuminated for 2s.
When all the doors are close, the display gets extinguished automatically if no key operation within 3 minutes. When the
display is off, it will light up if any door is opened or any key is pressed.
The following key operations are valid only when the keys are unlocked and gets illuminated on the display.
★Temp. setting
1)Fridge temperature setting
Press the 'Fridge' button, with the fridge temperature digits flickering, and then press the 'Fridge' key to adjust the
temperature, finally press the
setting.
The fridge temperature setting cycles as following:
5℃→6℃→7℃→8℃→OFF→2℃→3℃→4℃→5℃;
OFF refers to Fridge Off, and when OFF takes effect, the fridge will
stop cooling.
Take foods out of the fridge compartment before setting this
function.
2)Freezer temperature setting
Press the 'Freezer' button, with the freezer temperature digits
flickering, and then press the 'Freezer' key to adjust the temperature,
finally press the
OK
to validate the above temperature setting.
The freezer temperature setting cycles as following:
-18℃→-17℃→-16℃→-24℃→-23℃→-22℃→-21℃→-20℃→-19℃→-
18℃
★Smart
1)When the Smart function is enabled, the temperature of the fresh
food compartment is controlled at 4 ℃ , and that of the freezer
compartment at - 18℃, so that foods can be stored in the best condition
while the refrigerator is running more efficiently and with better
performance.
Under the Smart mode, the fresh food compartment temperature and the freezer compartment temperature are
subject to no change.
2)Enabling the Smart function
Press the Function key to select Smart until the corresponding icon gets flickering, and then press the OK key within
5s for confirmation. If the OK is not pressed within 5s, the setting will be invalidated.
3)Exiting the Smart function
OK
to validate the above temperature

Publicidad

loading

Este manual también es adecuado para:

Fgc-213xFgc-215dgFgc-227wgFgc-228bg