Environmental Protection; Technical Specifications - Metabo W 750-100 Manual Original

4 = wire brushes
5 = grinding with sanding paper
Accessories:
1.1 = grinding wheel
1.2 = cup wheel (ceramic)
1.3 = diamond cup wheel "masonry/concrete"
2.1 = cut-off wheel "metal"
2.2 = cut-off wheel "masonry/concrete"
2.3 = diamond cutting disc "masonry/concrete"
2.4 = dual-purpose diamond cutting discs
(combined grinding and cutting disc)
3.1 = diamond drill bits
4.1 = wheel brush
4.2 = cup brush
5.1 = flap disc
5.2 = backing pad for sanding sheets
prescribed guard:
Type A = cutting guard / guard incl cutting guard slip
for cutting-off operations
Type B = guard for grinding
Type C = guard for grinding and cutting-off
operations (combination)
Type D = guard for cup wheel
Type E = extraction guard for surface grinding
Type F = extraction guard for cutting-off operations
Other accessories:
(see also www.metabo.com)
A Two hole nut (12)
B M-Quick clamping nut (1)
C Clamping nut (tool-free) (14)
D Extraction hood clip
For a complete range of accessories, see
www.metabo.com or the accessories catalogue.
12. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
A defective mains cable must be replaced only with
a special, original mains cable from Metabo
available from the Metabo service.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.

13. Environmental Protection

The sanding dust generated may contain
hazardous materials: do not dispose of dust with
household waste, but at a special collection point
for hazardous waste.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: never dispose of
power tools in your household waste!
According to European Directive 2012/19/EU
on Waste from Electric and Electronic Equipment
and implementation in national law, used power
tools must be collected separately and recycled in
an environmentally-friendly manner.

14. Technical Specifications

Explanatory notes on the specifications on page 3.
Subject to change in accordance with technical
progress.
Ø = max. diameter of the accessory
t = max. permitted thickness of the clamping
max,1
shank on accessory when using two-hole
nut (12)
t = max. permitted thickness of clamping
max,2
shank on accessory when using "M-
Quick" clamping nut (1)
t = max. permitted thickness of clamping
max,3
shank on accessory when using (tool-
free) clamping nut (14)
t = roughing disc/cutting disc:
max,4
max. permitted thickness of accessory
t = max. permitted thickness of wheel-type
max,5
wire brushes
M = Spindle thread
l = Length of the sanding spindle
n * = No-load speed (maximum speed)
0
n * = No-load speed (adjustable)
V
P = Rated input power
1
P = Power output
2
m = Weight without mains cable
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~
AC power
The technical specifications quoted are subject to
tolerances (in compliance with relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on operating conditions, the
condition of the power tool or the accessories used.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user, such as
organisational measures based on the adjusted
estimates.
Total vibration value (vector sum of three directions)
determined in accordance with EN 60745:
a = Vibration emission value
h, SG
(surface grinding)
a = Vibration emission value
h, DS
(sanding with sanding plate)
K = Uncertainty (vibration)
h,SG/DS
Typical A-effective perceived sound levels:
L = Sound-pressure level
pa
L = Acoustic power level
WA
K , K = Uncertainty
pA WA
Wear ear protectors!
ENGLISH en
19