How To Read Product Label; Correct Positioning; Electric Connection - Lofra DOLCEVITA Instalación

How to read product
label
The product label is located inside the hood, usually at-
tached on its bottom, being visible after the removal of
the anti-grease filters.
The label shows essential data and information about the
product regarding installation, customer service and war-
ranty-related repair, as well as instructions to determine
the correct spare parts for the specific model.
Please do not remove, damage or alter in any way the
product label, since this could impede the Manufacturer
from identifying the product in case of need.

Correct positioning

The hood should be placed at a minimum distance of 65
cm for the wall-mounted models and 75 cm for the island/
roof models. It could be that Your specific hob requires the
range hood to be placed at a greater distance: always re-
fer to the manufacturer's instructions handbook for further
information.
The installation site must:
- be well ventilated and not exposed to weather conditions;
- Have a temperature between +16 and +32 °C (60.8-
89.6 °F) and an humidity below 60% (any variation from
the aforementioned values could accelerate the usual
decay time of the carbon filters decay or limit the overall
performance of the hood);
- comply with all the applicable regulation from the User's
country in terms of indoor air quality, electrical system
security and work safety;
- be suitable for the preparation of food.
For correct installation, refer to the drawings on
5 13
page to .
The equipment must be installed in a way that
ensures easy access to electric connections.
Do not use any electric wire or other electric devic-
es to extend the original power cord. Please inspect the
existing wall sockets or power cords of your kitchen and
place the hood accordingly;
The fastening kit (screws and plugs) supplied with
the hood can only be used on masonry wall. For
installation on other types of walls consider alter-
native fastening systems, taking into account the strength
of the wall and the weight of the hood.
Do not place the equipment near flammable
materials or flammable substance containers
(e.g. partition walls, gas cylinders, etc.), to
avoid fire hazards.
All the installation operations, assembly, connec-
tion to the electric power supply and extraordinary
maintenance must only be carried out by qualified
personnel, authorised by the Distributor or Manufacturer,
in accordance with the legal requirements of the country
of installation and in compliance with equipment and
workplace safety regulations.
The equipment must only be installed by responsible
and experienced adults, without physical impairment
and in perfect psychological and physical condition.
During installation, anyone and any objects not in-
volved in the assembly operations must be kept
away from the area.
Before starting the assembly operations, make
sure that all the necessary tools are available and in
good working order.

Electric connection

The electric connection can only be carried out
by qualified personnel (electrician).
The cable and the internal hood cables must
not be replaced or modified.
Before connecting the equipment to the power
mains:
- read the safety instructions provided at the
beginning of this manual;
- make sure that the electric system installed complies with
the local regulations of the country of installation;
- make sure that the electric system installed is suitable for
the characteristics of the equipment being installed (see
the details on the data plate).
Refer to chapter "
24
for further information on the data plate.
The equipment is supplied with the power supply cable
already attached: connect a suitable plug for the load to
the cable (the plug must comply with current standards).
Remember the following:
- yellow- green cable: earth;
- blue cable: neutral;
- brown cable: phase.
Always install a circuit breaker for quick disconnec-
tion. The earth cable must be not interrupted by
the circuit breaker.
If the power cord is faulty, it should be replaced with an-
other one with identical features. To prevent all kinds of
risks, such replacement must be carried out by the Man-
ufacturer, its technical support service, or in any case by a
similarly qualified individual. The Manufacturer is not liable
for any damage resulting from the use of unauthorized or
aftermarket spares.
Before any interventions inside the hood, disconnect the
electric power supply.
Avoid winding the cable on itself if too long. Make
sure that the cable is not in contact with liquids,
sharp or hot objects (temperatures exceeding
70°C), or corrosive substances.
24

How to read product label"

on page