Publicidad
Idiomas disponibles
Idiomas disponibles
ASSEMBLY INSTRUCTIONS
INSTALL THE HARNESS
WARNING:
Always use the shoulder harness when using the
cutting blade to avoid serious personal injury.
1.
Push the strap through the
center of the buckle.
2.
Pull the strap over the cross
bar and down through the
slot in the buckle (Fig. 11).
3.
Put the harness on over head
and onto shoulder. Snap it on
to the support fitting (Fig. 12).
4.
Adjust length to fit the
operator's size. Pull tab to
lengthen, pull strap to
shorten (Fig 13).
OIL & FUEL INFORMATION
OIL AND FUEL MIXING INSTRUCTIONS
Old and/or improperly mixed fuel are the main reasons for the unit not
running properly. Be sure to use fresh, clean unleaded fuel. Follow the
instructions carefully for the proper fuel/oil mixture.
Definition of Blended Fuels
WARNING:
It has been proven that fuel containing greater than
10% ethanol will likely damage this engine and void the warranty.
Today's fuels are often a blend of gasoline and oxygenates such as ethanol,
methanol, or MTBE (ether). Alcohol-blended fuel absorbs water. As little as 1%
water in the fuel can make fuel and oil separate. It forms acids when stored.
When using alcohol-blended fuel, use fresh fuel (less than 30 days old).
Using Blended Fuels
CAUTION:
For proper engine operation and maximum
reliability, pay strict attention to the oil and fuel mixing instructions
on the 2-cycle oil container. Using improperly mixed fuel can
severely damage the engine.
• If choosing to use a blended fuel, or its use is unavoidable, follow
recommended precautions:
• Always use the fresh fuel mix explained in the operator's manual
• Always agitate the fuel mix before fueling the unit
• Drain the tank and run the engine dry before storing the unit
Using Fuel Additives
It is recommended to use the manufacturers 2-cycle oil with this unit. If
unavailable, use a good 2-cycle oil designed for air-cooled engines along
with a fuel additive, such as STA-BIL® Gas Stabilizer or an equivalent. Add
0.8 oz. (23 ml.) of fuel additive per gallon of fuel according to the instructions
on the container. NEVER add fuel additives directly to the unit's fuel tank.
Mixing The Fuel
Thoroughly mix the proper ratio of 2-cycle engine oil with unleaded fuel in a
separate fuel can. Use a 40:1 fuel/oil ratio. Do not mix them directly in the
engine fuel tank. See the table for specific gas and oil mixing ratios.
IF...
NOTE:
NOTE:
Fig. 11
FUELING THE UNIT
Support
Fitting
Fig. 12
1.
2.
NOTE:
3.
4.
Fig. 13
5.
NOTE:
STARTING INSTRUCTIONS
1.
2.
NOTE:
3.
6
OIL & FUEL INFORMATION
the unit came with a bottle of
2-cycle oil; pour the entire
bottle into 1 gallon of gas
and mix thoroughly.
One gallon (3.8 liters) of
unleaded fuel mixed with
one 3.2 oz. (95 ml.) bottle
of 2-cycle oil makes a
40:1 fuel/oil ratio.
Dispose of the old fuel/oil
mix in accordance to
federal, state and local
regulations.
WARNING:
Gasoline is extremely flammable. Ignited vapors
may explode. Always stop the engine and allow it to cool before
filling the fuel tank. Do not smoke while filling the tank. Keep
sparks and open flames at a distance from the area.
WARNING:
Remove fuel cap slowly to avoid injury from fuel
spray. Never operate the unit without the fuel cap securely in place.
WARNING:
Add fuel in a clean, well ventilated outdoor area. Wipe
up any spilled fuel immediately. Avoid creating a source of ignition for
spilt fuel. Do not start the engine until fuel vapors dissipate.
Turn unit on its side, with the
fuel cap facing up, and
remove the fuel cap.
Place the gas container's
spout into the fill hole on the
fuel tank and fill the tank.
(Fig. 14)
Do not overfill the tank.
Wipe up any gasoline that
may have spilled.
Reinstall the fuel cap.
Move the unit at least 30 ft. (9.1 m) from the fueling source and site
before starting the engine.
STARTING/STOPPING INSTRUCTIONS
WARNING:
Operate this unit only in a well-ventilated outdoor
area. Carbon monoxide exhaust fumes can be lethal in a confined
area.
WARNING:
Avoid accidental starting. Make sure to be in the
starting position when pulling the starter rope (Fig. 18). To avoid
serious injury, the operator and unit must be in a stable position
while starting.
This unit uses the Incredi-Pull™ starting system, which significantly
reduces the effort required to start the engine.
Mix gas with oil. See Oil and
Fuel Mixing Instructions.
Fill the fuel tank with the
fuel/oil mixture.
There is no need to turn
the unit on. The On/Off
Control is in the ON ( I )
position at all times
(Fig. 15).
Fully press and release the
primer bulb 10 times, slowly.
Some amount of fuel should
be visible in the primer bulb and fuel lines (Fig. 16). If fuel can not be seen
in the bulb, press and release the bulb as many times as it takes until fuel
can be seen in it.
UNLEADED GAS
2 CYCLE OIL
1 GALLON US
3.2 FL. OZ.
(3.8 LITERS)
(95 ml)
1 LITER
25 ml
MIXING RATIO - 40:1
Fig. 14
Off (O)
On ( I )
Throttle
Control
Fig. 15
Publicidad
Solución de problemas
