Publicidad
position and release the knob (18), Fig.12.
Place the nut (98), fit the screws (74) and the washers
(75), Fig.12.
13.- Fix the pulleys (32) using the screws (109), the
washers (11) and the nuts (10), Fig.13.
Pass the cable (39) through the pulleys (32) as shown in
Fig.13.
Assemble the pulleys (A), (B) and (C) using the screws
(108), the bushings (99), the washers (11) and the nuts
(10) as shown in Fig.13, 1.
Assemble the pulley (D) using the screw (119), the washer
(11) and the nut (10) as shown in Fig.13, 2.
Assemble the pulleys (E) and (F) placing the supports (25)
and using the screws (109), the washers (11) and the nuts
(10) as shown in Fig.13, 3.
Pass the cable (39) through the pulleys as shown in
Fig.13 and fix the end of the cable to the rod (29), Fig.8.
14.- Fix the position of the pulleys (32) in the butterfly
assembly (96). Fit the screws (116), the washers (104)
and the nuts (101), Fig.14.
15.- Pass the cable (39) through the cover (41) and the
shaft (42) Fig.15.
Hook one end of the chain (44) to the shaft (42) and the
other end to the bar (77), Fig.15.
16.- Assemble the pulleys (H) using the screws (119), the
washers (11) and the nuts (10) as shown in Fig.16, 2.
Assemble the pulley (G) placing the supports (25) and
using the screws (109), the washers (11) and the nuts (10)
as shown in Fig.16, 4.
Assemble the rest of the pulleys using the screws (109),
the washers (11) and the nuts (10), Fig.16.
Pass the cable (37) through the pulleys as shown in
Fig.16.
17.- Pass the cable (37) through the cover (41), the shaft
(42) and hook it to the biceps rope (46), Fig.17.
Pass the other end of the cable (37) through the cover
(41), the shaft (42) and hook it to the pull bar (83), Fig.17.
18.- Fix the pulley (32) on the support (25) using the screw
(109), the washer (11) and the nut (10), Fig.18.
Pass the cable (40) through the pulley, fix one end (36) to
the hook (43), Fig.18.
Pass the other end of the cable through the spring (45)
and secure it to the assembly (22) using the nut (35),
Fig.18.
19.- Assemble the pulleys (32) as shown in Fig.19, fix
them using the screws (109) and the washers (11). To fix
the pulleys at points (J) and (K) you only need the screws
(109), Fig.19.
20.- To fit the handles, pass the cable (38) through the
cover (41) and the shaft (42) and connect it to the hook
(43), Fig.20.
21.- Place the covers (52), (53), (54), (55) using the
screws (118) and the washers (105), Fig.21.
22.- Attach the left cover (48) and fix it to the upper frame
(20) and the base frame (1) using the screws (121) and
the washers (103), Fig.22.
23.- Place the right cover (49) and fix it to the upper frame
(20) and the base frame (1) using the screws (121) and
the washers (103), Fig.23.
Place the middle cover (50) and fit the screws (122) and
the washers (107), Fig.23.
Do not hesitate to get touch with the Technical Assistance
Service if you have any queries by phoning customer
services (see last page in manual).
BH RESERVES THE RIGHT TO MODIFY THE
SPECIFICATIONS OF ITS PRODUCTS WITHOUT
PRIOR NOTICE.
19
Publicidad
