General Use - Bell & Ross BR 05 chronograph Manual De Instrucciones

0 1 2 3
ENGLISH
BR 05 CHRONOGRAPH
BR-CAL.326
: mechanical with automatic winding. Calibre BR-CAL.326. Power reserve approximately 56 hours.
Movement
3 o'clock, central chronograph seconds.
Case

GENERAL USE

Starting the watch
0 1 2 3
When the watch has stopped (crown in position 0): unscrew the crown
(turn anticlockwise) to position 1. Wind the movement by turning the
0 1 2 3
crown clockwise. After approximately 40 rotations, the watch is fully
wound (the winding mechanism does not have a stop to prevent over-
winding). The power reserve is approximately 56 hours when fully
wound. When the watch is worn , the automatic mechanism will wind
the movement.
resistance, screw the crown back into position 0. Never operate the
crown underwater.
Setting the time
0 1 2 3
Unscrew the crown then pull it out to position 3. The seconds hand
will stop, enabling the time to be set to the nearest second. Set the
time by rotating the crown in the required direction.
0 1 2 3
0 1 2 3
0 1 2 3
USING THE CHRONOGRAPH
The chronograph function can measure time in minutes and seconds.
60 seconds counter
0 1 2 3
0 1 2 3
0 1 2 3
0 1 2 3
0 1 2 3
Chronograph 30-minute counter
IMPORTANT
Magnetic fields . Magnetic fields can adversely affect the accuracy of your watch. Also, we would
recommend that you avoid placing your watch near electronic devices that may generate large
magnetic fields (radio, smartphone, television, computer, tablet, loudspeakers, etc.).
NOTE : the slotted screws mount the bezel to the case and ensure the water resistance of the
watch. To benefit from the Bell & Ross warranty, these screws must never be unscrewed.
MAINTENANCE
After being immersed in seawater, it is recommended to carefully rinse off the watch and strap with
fresh water. It is also recommended to have the water resistance of your watch checked every two
years. To ensure a service that meets the brand's exacting standards, any servicing of your watch
must be carried out by the Bell & Ross service centre or a watchmaker approved by Bell & Ross.
Whenever repairs are made during the warranty period, you must present the Bell & Ross warranty
card, duly dated and signed by the retailer at the time the watch was purchased.
: 42 mm in width.
: Once the watch is set, to ensure perfect water
NOTE
30 minutes counter
Minute hand
P
1
Chronograph 60-second hand
Hour hand
Seconds hand
P
2
Case attachment screw
(NEVER UNSCREW)
0 1 2 3
: hours, minutes, small seconds at 9 o'clock and date. Chronograph: 30-minute counter at
Functions
P
1
0 1 2 3
Setting the date
Quick setting
Crown in position 2: unscrew and pull the crown out to position 2 and
0 1 2 3
set the date by turning the crown anticlockwise.
mechanical watches with a date function, quickset date setting MUST
P
2
NOT UNDER ANY CIRCUMSTANCES be carried out between the times
of 9 PM (21.00) and 3 AM (3.00).
Slow setting
0 1 2 3
Crown in position 3: to ensure the date changes at midnight rather
than noon, it is recommended to set the date by adjusting the hands of
P
the watch. Unscrew and pull the crown out to position 3 and turn the
1
hands until the date changes. Then set the precise time.
0 1 2 3
P
2
Measuring a time period
First press of Pusher P1: sets off the time measurement.
Second press of Pusher P1: stops the time measurement.
Third press of Pusher P2: stops and resets the chronograph.
P
P
1
1
Measuring a time period with an interruption
First press of Pusher P1: sets off the time measurement.
Second press of Pusher P1: stops the time measurement.
Third press of Pusher P1: restarts the time measurement.
This allows one or more time intervals to be subtracted from the total time
P
P
2
2
measured.
Fourth press of Pusher P1: stops the time measurement.
Fifth press of Pusher P2: stops and resets the chronograph.
INTERNATIONAL WARRANTY
To benefit from your 2-year international warranty, your card must be activated at the time of
purchase by your approved Bell & Ross point of sale, and presented every time an operation is
performed. You can now access the digital version of this card and all the information relating to
your watch by scanning the QR code or visiting:
To ensure a service that meets the brand's exacting standards, any servicing of your watch must
be carried out by the Bell & Ross service centre or a watchmaker approved by Bell & Ross. The
warranty does not, however, include:
. Any damage caused by accidents or by inappropriate or improper use of the watch (e.g. violent
impacts, crushing, rough handling of the clasp).
. Any damage caused by repair or disassembly operations carried out by a retailer or after-sales
service centre not approved by Bell & Ross.
. The consequences of the watch and bracelet/strap ageing and normal wear and tear.
3
NOTE : as with all
Pusher 1 (P1)
Start/Stop
Crown
Pusher 2 (P2)
Reset
Date
www.bellross.com/warranty.