Publicidad
Idiomas disponibles
Idiomas disponibles
1. Before assembling the model:
Please check the contents of your kit before you start construction.
You will find Figs. 01 + 02 and the Parts List helpful here.
2. Right / left fuselage shells
The moulding process leaves bridging lugs at the front of the
fuselage shells 4 + 5, which should now be removed using a
sharp balsa knife.
Fig. 03
Examine the air intakes, and remove any rough edges from the
lips using a very sharp knife. If this leaves areas of a different
colour, touch them in with a soft pencil.
Right-hand fuselage shell
3. Gluing the nose section to the fuselage shell
Trial-fit the fuselage nose 8 and the right-hand fuselage shell 5,
then glue the parts together using cyano. Take care to line the
parts up accurately.
Fig. 04
4. Installing the fuselage stiffener
Glue the GRP rod 41 in the fuselage shell using cyano. Glue the
rod over its full length, but don't apply so much cyano that it is
forced out of the joint.
Fig. 05
5. Glue the canopy latch catch 22 in the fuselage nose section
8.
Fig. 06
6. Installing the elevator servo
The elevator servo can be glued in its recess using two drops of
cyano or hot-melt glue. Be sparing with the adhesive, otherwise
it may be difficult to remove the servo again if it should require
repair at any time. Too much adhesive can also penetrate the
servo case, with the danger of jamming the gearbox.
Deploy the servo lead in the channel provided. If you are using
an extension lead with a plug-in connection, cut a small recess
in the fuselage for the connectors. If you have soldering facilities,
it is always preferable to solder the connections.
Secure the loose cable with adhesive tape so that it does not get
in the way during the following procedures.
Fig. 07
7. Trim ballast
If you use the recommended components, you will need to glue
the two ballast weights 34 in the space provided at the tail end of
the fuselage. If lighter batteries become available in the future,
you may be able to take the weights out again; you can remove
one ball for each 20 g saved at the battery compartment position.
Fig. 08
8. Aileron servo lead
Glue the extension lead to the inside of the fuselage, with the
socket flush with the outside surface, so that the aileron servo
lead can be plugged in later when the wings are fitted.
Fig. 09
Left-hand fuselage shell
9. Gluing the nose section to the fuselage shell
Trial-fit the fuselage nose 7 and the right-hand fuselage shell 4,
then glue the parts together using cyano. Take care to line the
parts up accurately.
Fig. 10
10. Installing the fuselage stiffener
Glue the GRP rod 41 in the fuselage shell using cyano. Glue the
rod over its full length, but don't apply so much cyano that it is
forced out of the joint.
Fig. 11
8
Glue the stiffener 41 to the inside of the fuselage in the same
manner.
Fig. 12
11. Glue the canopy latch catch 22 in the fuselage nose section
7.
Fig. 13
12. Glue the extension lead to the inside of the fuselage, with
the socket flush with the outside surface, so that the aileron
servo lead can be plugged in later when the wings are fitted.
Fig. 14
13. Joining the fuselage shells
Start by trial-fitting the fuselage shells "dry" (no glue); they should
fit together snugly, without requiring force and without being under
tension. If there is a tight spot at any point, trim the parts where
necessary before gluing the shells together using thick cyano.
You will have a few minutes to get everything right, so work swiftly
but not hurriedly. Join the fuselage shells, immediately line them
up correctly, and hold the parts together until the glue starts to
set. Do not resume work on the fuselage for a few minutes as
the adhesive takes some time to cure properly.
Fig. 15
14. Aileron horns (both ailerons)
The aileron horns 24 are prepared and installed as shown in
the illustration: 1 x left + 1 x right. Tighten the nuts 27 only lightly,
as the swivel pushrod connectors 25 must turn smoothly. Secure
the nuts with a tiny drop of paint or glue.
Caution: only apply the paint or glue to the outside of the nut
and the stub of the thread.
Glue the horns in the aileron recesses.
Fig. 16
15. Installing the servos and pushrods (both ailerons)
Check from the transmitter that the aileron servos work correctly,
and set them to centre. Fit the output levers on the servo shafts,
ensuring that the arms project out of the wings (see illustration).
Fit the servo arm retaining screws. Fix the servos in their recesses
with a few drops of cyano or hot-melt glue. Connect the aileron
pushrods 30 and adjust them.
Fig. 17
16. Freeing the ailerons (both ailerons)
Carefully release the ailerons by cutting along the marked lines;
the slots should be about 1 mm wide. You will need a very sharp
knife to cut the foam cleanly.
Fig. 18
17. Gluing the wing panels 10 + 11 to the fuselage, connecting
the aileron servos
First connect the aileron servo leads (in the wings) to the
extension leads which you have already installed in the fuselage.
Leave the leads loose in the channels. Glue the wings to the
fuselage, taking care not to glue the cables. Align the wings
carefully before allowing the glue to cure.
Fig. 19
18. Installing the wing spar
Slide the wing spar under the servo leads and through the
fuselage, then glue it in place along its full length.
Fig. 20
19. Servo leads and servo fairings
Deploy the servo leads in the channels in the wings, starting
from the servo end. You may need to use the blunt side of a knife
to push them into the slot. The excess length of the servo leads
Publicidad
