Publicidad
Idiomas disponibles
Idiomas disponibles
RF Spectrum Analyzers
INPUT AND OUTPUT CONNECTIONS
1.DC POWER
DC power to operate and/or recharge the instrument is connected via a 1.3mm power socket .
INPUT*
CAUTION
The adaptor/charger supplied has a universal input voltage rating of 100-240VAC, 50/60Hz. It
is a Class II (double insulated) device, fully approved to EN 60950-1 and UL 60950-1 (UL listing E245390).
Use ONLY the power-supply/charger provided by Aim-TTi with the unit. Use of any other power source
will void the warranty.
2.RF SIGNAL
The signal to be measured is connected via a standard N connector. The input impedance is 50 Ohms.
INPUT
CAUTION
PSA3605/6005- The maximum useable signal input is +20dBm or +127 dBuV. The absolute
maximum signal input level is +25dBm or +132dBuV of RF power (approximately 4 volts RMS), or 50V DC.
PSA1303/2703- The maximum useable signal input is +10dBm or +117 dBuV. The absolute maximum
signal input level is +23dBm or +130dBuV of RF power or 50V DC. Applying a signal above this level could
damage the unit and such damage would not be covered by the product warranty.
3.DEMODULATED
Demodulated audio (when in Zero Span Mode) is available via the built-in speaker, the signal is also
AUDIO OUTPUT
provided via a 3.5mm stereo jack socket. Maximum power output is 30 milliwatts into 32 Ohms.
4.USB HOST
For USB Flash Memory.
5.USB MINI-B
For connection to a PC.
6.TRIGGER
A 3.5mm mono jack socket is mounted at the top of the instrument for trigger signals.
INPUT/OUTPUT
This has no function unless option U01/U02 is fitted. An adaptor is provided
that converts from the jack socket to a standard BNC connector.
BATTERY OPERATION
NOTE
As supplied, the internal battery is likely to be partially charged. The instrument should
therefore be plugged into its charger for at least two hours before first use.
CHARGING
THE BATTERY
Charging
Charged
Full charge <3hrs
Approx. remaining battery life
BATTERY
STATUS
5hr
4hr
3.5hr
3hr
2hr
Series 3:
3.5hr
3hr
2.5hr
2hr
1.5hr
Series 5:
POWER
SAVING
TIPS
10%
Screen brightness
5% steps (Default 40%)
4
NOTE
MiniUSB
It is not possible to operate the
OFF
instrument from USB power. For
bench top operation, use the
Slow Charging
supplied ac-line charger.
Full charge >10hrs
Approx. remaining battery life:
Status
System information
1hr
45min 30min 10min
Battery: 80% 3hour 2min remaining
1hr
45min 30min 10min
=
-1hr
100%
Auto Off
100%
(5 min, 15 min, 30 min, 60 min)
Aim-TTi - Safety Documentation & Quick Start Guide
GETTING STARTED
Aim-TTi - Safety Documentation & Quick Start Guide
RF Spectrum Analyzers
It is recommended that all users,
including those fully familiar with
RF spectrum analyzers, take a little
time to read through this manual
before
using
the
instrument.
However, for users who wish to get
started with hands-on operation as
quickly as possible, the following
may prove useful:
1
Primary Status Information
TRACE AREA
2
Graticule and Level Marks (grey)
Live Trace (green)
Marker M1 (yellow)
Marker M2 (light blue)
View Trace (white)
Reference Trace (purple)*
3
Marker Readout
4
Battery Status
5
Sweep Control Key
6
Secondary Status Information
TOUCH SCREEN CONTROL KEYS
7
Menu Groups
8
Sub-Groups
9
Functions
HARD KEYS
10
Exit a Function Menu
11
Show Instrument Status |
Help Screens | Access System
12
Navigator (5 keys)
13
Set Mode for Navigator
14
Turn Instrument On or Off
15
Access Presets and Auto-Set
16
Write Live trace to View trace
17
Control Sweep | Manual Log
18
Stylus
*Not Shown
5
Publicidad
