Etac R82 Kudu Manual De Instrucciones página 42

Safety
Signs, symbols and instructions placed on this product must never be covered or removed and must remain present and
clearly legible throughout the entire lifetime of the product. Immediately replace or repair illegible or damaged signs, symbols
and instructions. Contact your local dealer for instructions.
In case of an adverse event occurred in relation to the device, incidents should be reported to your local dealer and the
national competent authority in a timely manner. The local dealer will forward information to manufacturer.
Caregiver
• Read the "User Guide" carefully before use and keep
it for future reference. Incorrect use of this product
may cause serious injury to the user
• Settings and adjustments to the product or
accessories are only to be made by persons who have
read the user manual.
• This product contains small parts which could present
a choking hazard if removed from their intended
placing
• Always use the correct lifting techniques and aids for
this purpose
• Never leave the user unattended in this product.
Ensure permanent supervision by a caregiver
• Be aware of any MAX mark indications before
adjustment
• Repair/replacements must only be made using new
original R82 spare parts and fittings and carried
out in accordance with the guidelines and service
intervals prescribed by the supplier
• If there is any doubt as to the continued safe use
of your R82 product or if any parts should fail, stop
using the product immediately and contact your local
dealer as soon as possible
• Ensure that moving parts does not squeeze or trap
body parts when adjusting them
• Ensure that body parts are not trapped in openings
for mounting of supports/accessories.
• Information about transportation can be found in the
document "M1460 Transportation in Motor Vehicles"
supplied with the product
• Information about roadability can be found in the
document "Roadability" supplied with the product
Environment
• Observe the surface temperature on the product,
before placing a user in it. This goes especially for
users with insensitive skin as they cannot feel the
heat. If the surface temperature is above 41°C then
allow the product to cool before use
• Use this product on a level surface without any
obstacles. Be aware of reduced maneuverability on
slippery surfaces
• When using on inclines, please refer to
measurements
User
• If the user is close to the max. load limit and/or
has a lot of involuntary movements, e.g. rocking, a
larger size with a higher max. load or a different R82
product should be considered
Product
• Carry out all positional adjustments on the product
and accessories and ensure that all knobs, screws
and buckles are securely fastened before use. Keep
all tools out of the reach of children
• Removable parts without use of tool: wheels, foot
support and cushions. The removal will have adverse
effect on the device
• Activate the brakes before placing the user into the
product
• Activate the anti-tips when the product is being used
on inclines
• Activate the anti-tips before angling the seat and back
• Deactivate the anti-tips when forcing kerbs higher
EN
than 100 mm
• Ensure the stability of the product is maintained
before placing the user in it
• We recommend you notify the user before angling the
seat and back
• Ensure the wheels are fully-functional and secure
before use
• The correct tyre pressure is printed on the tyre casing
and listed in the section for tyre technical data.
• In case of a tyre puncture do not use the product until
remedied
• Unoccupied device is suitable for land and air
transport
• Attaching additional loads can adversely affect
stability. Position of points intended to carry
additional loads are specified in the relevant
Mounting Guide referred to under section for
accessories
• Do not expose the gas spring to pressure or high
temperatures. DO NOT puncture
• Inspect the product and all of its accessories and
replace any worn out parts before use
• This product is tested for resistance to ignition at
level non-ignition in accordance with EN 1021-2 and
ISO 7176-16
• The product might lose its flame resistant
characteristics if using other than original R82:
Cushions
• The product is approved for transportation in vehicles
according to ISO 7176-19. More information can be
found in the document "M1460 Transportation in
Motor Vehicles" supplied with the product.
• In accordance with ISO 7176-19 Annex D, the product
is evaluated regarding the ability to accommodate
vehicle-anchored pelvic and shoulder belts. The
device receives an overall score of "Good"
42
etac.com