Publicidad
Idiomas disponibles
Idiomas disponibles
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
This equipment should be installed and serviced by technically
qualified personnel who are familiar with the correct selection
and use of appropriate tools, equipment, and procedures. Failure
to comply with national and local electrical and plumbing codes
and within FPS recommendations may result in electrical shock or
fire hazard, unsatisfactory performance, or equipment failure.
Know the product's application, limitations, and potential haz-
ards. Read and follow instructions carefully to avoid injury and
property damage. Do not disassemble or repair unit unless
described in this manual.
Failure to follow installation or operation procedures and all
applicable codes may result in the following hazards:
Risk of death, personal injury, or
property damage due to explosion, fire,
or electric shock.
•
Do not use to pump flammable or explosive fluids such as gaso-
line, fuel oil, kerosene, etc.
•
Do not use in explosive atmospheres or hazardous locations as
classified by the NEC, ANSI/NFPA70.
•
Do not handle a pump or pump motor with wet hands or when
standing on a wet or damp surface, or in water.
•
When a pump is in its application, do not touch the motor, pipes,
or water until the unit is unplugged or electrically disconnected.
•
If the power disconnect is out of sight, lock it in the open position
and tag it to prevent unexpected application of power.
•
If the disconnect panel is not accessible, contact the electric
company to stop service.
Risk of severe injury or death by
electrical shock.
•
To reduce risk of electrical shock, disconnect power before work-
ing on or around the system. More than one disconnect switch
may be required to de-energize the equipment before servicing.
•
Wire pump system for correct voltage.
•
Do not use an extension cord; provide a properly located control
panel or junction box.
•
For single-phase motors, ensure power, neutral, and ground
wires are properly connected. If not, a qualified, licensed electri-
cian should correct the problem.
•
These pumps are supplied with lead wires and are intended to be
hardwired using a junction box or other approved enclosure. The
pump includes a grounding conductor. To reduce risk of electric
shock, be certain that it is properly connected to ground.
•
To avoid hazards when installing or servicing, install a double-
pole disconnect near the pump installation.
•
If the supply cord is damaged, it must be replaced by the manu-
facturer, its service agent, or similarly qualified persons in order
to avoid a hazard.
2
Risk of severe injury or death by
electrical shock.
•
Check local electrical and building codes before installation. The
installation must be in accordance with their regulations as well
as the most recent National Electrical Code (NEC) and the Occu-
pational Safety and Health Act (OSHA).
•
Do not use the power cord for lifting the pump.
•
The pump should only be used with liquids compatible with pump
component materials. If the pump is used with liquids incompati-
ble with the pump components, the liquid can cause failure to the
electrical insulation system resulting in electrical shock.
Risk of bodily injury, electric shock,
or equipment damage.
•
This equipment must not be used by children or persons with
reduced physical, sensory or mental abilities, or lacking in experi-
ence and expertise, unless supervised or instructed. Children
may not use the equipment, nor may they play with the unit or in
the immediate vicinity.
•
Equipment can start automatically. Always unplug the pump power
cord and disconnect the electrical power before servicing the pump.
•
Do not run the motor or pump dry (without liquid) for more than
15 minutes. If run dry, the surface temperature of the pump will
rise to a high temperature that could cause skin burns if touched
and will cause serious damage to the pump. Refer to the motor
manual.
•
Do not let the unit freeze. Freezing may cause cracking or distor-
tion that may destroy the unit.
•
An inoperative or malfunctioning pump could lead to flooding,
resulting in personal injury or property damage.
•
The pump has been evaluated for use with water only. Pump
should only be used with liquids compatible with pump compo-
nent materials.
•
Operation of this equipment requires detailed installation and
operation instructions provided in the pump, motor, and control
panel manuals provided with this product. Read the entirety of all
manuals before starting installation and operation. End User
should receive and retain all manuals for future use.
•
Keep safety labels clean and in good condition.
•
Keep work area clean, well-lit, and uncluttered. Wear safety
glasses while installing or performing maintenance on the pump.
Publicidad
