Bosch FSA 050 Instrucciones De Funcionamiento página 27

5. Operation
The following description relates primarily to usage of the FSA 050 as a stand-alone unit. Bluetooth opera-
tion of the FSA 050 is described in the Online Help of the CompacSoft[plus] software. Installation of the
CompacSoft[plus] software on a PC/Laptop is described in Section 5.13.
i
If the FSA status is set in the SETUP menu, FSA 050 blocks the insulation test and the display/deletion of the
stored results in Stand-alone mode.
�.1 �ETUP menu
The SETUP menu enables users to set values for use
with the various FSA 050 functions. In the following
table, the symbols and their significance are described
in the order in which they are displayed.
�ymbol Meaning
Status set:
tYP
��A – FSA 050 communication via Bluetooth with FSA 500/7xx.
�TA – FSA 050 operation in stand-alone mode.
Sets the buzzer threshold for continuity
bU2
measurements. The buzzer sounds if the
measurement result is below the set value.
Lock button ON/OFF
L0C
Sets the maximum current level for short
l5C
circuits with continuity measurements.
Sets the lower threshold in ohms for the
ln5
buzzer for insulation analysis. The buzzer sounds if the result is above the
set value.
Timer for insulation analysis mode t. Insulation analysis is terminated once
t
the time has run down to 0 seconds. Insulation analysis is
active during the countdown.
Limit value for interference voltage detection during insulation analysis.
5Et
Restore standard setting YES/NO
r5t
i
Turning the rotary switch to a different position
always terminates the SETUP menu.
�ETUP – �etting status
1. Set the rotary switch to <�ETUP> (Fig. 2, Pos. 6).
 The firmware version of the FSA 050 is displayed
for four seconds and then
 The status of the FSA 050 (FSA or STA).
2. Press <TE�T> (Fig. 2, Pos. 1) for approx. two se-
conds.
 The status of the FSA 050 changes.
 The buzzer sounds briefly.
 The lock symbol
on the LCD flashes.

3. Briefly pressing <TE�T> changes the status (FSA/
STA) of the FSA 050.
4. Press < /OK> to store the desired value

(Fig. 2, Pos. 2).
¶
The desired value has been stored when the lock
symbol disappears from the LCD.

Robert Bosch GmbH
Operation | ��A ��� | 27
�tandard
setting
STA
2 Ω
on
200 mA
0.5 M?
1 minute
12 V
no
�ETUP – �etting values
1. Set the rotary switch to <�ETUP>.
 The firmware version of the FSA 050 is displayed
for four seconds and then
 The status of the FSA 050 (FSA or STA).
2. Briefly press <TE�T> once.
 The first symbol and its value are displayed (
3. The next symbol is displayed by briefly pressing
<TE�T> once.
4. Keep briefly pressing <TE�T> until the display shows
the symbol for which the value is to be altered.
5. Press <TE�T> for roughly one second until the lock
symbol on the LCD flashes.

6. Keep briefly pressing <TE�T> until the desired value
is displayed.
i
While ever the lock symbol
displayed has not been stored.
7. Press < /OK> to store the desired value.

¶
The desired value has been stored when the lock
symbol disappears from the LCD.
en
�etting values
STA/FSA
1/2/5/10/20 Ω
On/Off
20/200 mA
0.5/1/2/5/10/20 M?
1 minute to 10 minutes
(in increments of one mi-
nute)
5/6/12/24 V
No/Yes
).
bU2
is flashing, the value

|
1 689 989 102 2011-04-26
1