Special Safety Instructions - Metabo KHE 2650 Instrucciones De Manejo

d)Store idle power tools out of the reach of
children and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
e)Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tool's operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g)Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
5) Service
a)Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained.

3. Special Safety Instructions

Wear ear protectors. Exposure to noise can cause
hearing loss.
Use the auxiliary handles supplied with the
tool. Loss of control can cause personal injury.
Hold power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the
operator an electric shock.
Work only with the additional handle correctly
installed.
Always hold the machine with both hands using the
handles provided, stand securely and concentrate.
Dust from material such as paint containing lead,
some wood species, minerals and metal may be
harmful. Contact with or inhalation of the dust may
cause allergic reactions and/or respiratory diseases
to the operator or bystanders.
Certain kinds of dust are classified as carcinogenic
such as oak and beech dust especially in
conjunction with additives for wood conditioning
(chromate, wood preservative). Material containing
asbestos must only be treated by specialists.
- Where the use of a dust extraction device is
possible it shall be used.
- The work place must be well ventilated.
- The use of a dust mask of filter class P2 is
recommended.
Follow national requirements for the materials you
want to work with.
Always wear protective goggles, gloves, and sturdy
shoes when working with this tool.
Ensure that the spot where you wish to work is
free of power cables, gas lines or water pipes
(e.g. using a metal detector).
Smaller workpieces must be secured such that they are
not carried along with the drill bit when drilling (e.g. by
clamping in a vice or on a work bench with screw
clamps).
If the safety coupling responds, switch off the
machine immediately.
Do not touch the rotating tool!
Remove chips and similar material only with the
machine at standstill.
Caution with hard screwdriving (driving of screws
with either a metric or an imperial thread into steel)!
The head of the screw may rip off or high restoring
torques may be incurred at the handle.
Pull the plug out of the plug socket before any
adjustments or servicing are performed.
Safety coupling: If the tool jams or catches, the
power supply to the motor is restricted. Due to the
strong force which can arise, always hold the
machine with both hands using the handles
provided, stand securely and concentrate.
SYMBOLS ON THE TOOL:
...... Class II Construction
V .......... volts
A .......... amperes
Hz ........ hertz
W......... watts
BPM..... beat per minute
~
.......... alternating current
n ......... no-load speed
0
rpm ...... revolutions per minute
.../min... revolutions per minute
4. Overview
See page 2.
1 Keyless chuck *
2 SDS chuck
3 Tool lock
4 Keyless chuck sleeve *
5 Chuck lock
6 Spindle
7 Wing screw (for adjusting the depth stop)
/ Lever (for adjusting the depth stop) *
8 Depth stop
9 Speed preselection wheel*
10 Electronic signal indicator*
11 Rotation selector switch
12 Lock button
13 Trigger
14 Switch button (for changing the operating
mode)
15 Lock
16 Additional handle
17 Safety coupling
* depending on model
ENGLISH en
5