Publicidad
Idiomas disponibles
Idiomas disponibles
CONTROLLER FUNCTIONS
After you've turned the unit on by pressing the
control knob you can access the following functions:
CLEAN OUT
The cleanout function is used to remove the last remaining
pellets from the pellet hopper and auger tube.
OPERATING THE CLEAN OUT FUNCTION
1.
Push the control knob once to turn the unit on. The controller will flash
several times and then turn to a solid screen. This lets you know your
unit is powered on.
2. Push the control knob again, this will take you to the function screen
where you can access the Temperature (F/C), Time, Meat Probe
Temperature, Prime, and Cleanout functions, as well as the Battery
level, A/C adapter, Fan, Auger, Igniter, and Battery removal indicators
(when applicable.)
3. *Once you've turned the unit on by pushing the control knob* Rotate
the control knob to select the Cleanout function. Push the button to
lock in the cleanout function.
4. The cleanout function is set to run for 90 minutes. The remaining pellets
will be fed through the burn pot into the 5-gallon bucket below.
you can shut off the Clean Out function at any time. You must reinsert
the ash tray back in place before starting the unit. Failure to insert the
tray back may cause fire and body injury.
IMPORTANT TO NOTE:
• The unit must be OFF, the AC adapter unplugged, and the battery
removed before cleaning out the hopper manually.
• The unit must be cool before the Clean Out function is initiated. Do not
use this function during startup or cooking foods. Failure to do so may
cause fire inside the fire pot and cause damage to your pellet grill.
• Place a container large enough to hold the discarded pellets under
the pellet clean-out fire pot opening. Pull the ash tray spring and
then slide the ash tray forward to align the ash tray clean out directly
under the fire pot to remove any ash. (Note: Release the spring pin as
soon as you start to pull the tray forward to lock the tray into the ash
clean-out position). Pull the ash tray spring pin once more to remove
the tray completely out from the unit to empty the ash. See the
Prime550 Pellet Clean Out section for details.
PRIME
The Prime function allows you to feed pellets into the burn pot to initially start
your unit or to feed additional pellets during a smoke to get more smoke.
1. Rotate the knob to select the Prime function.
2. Push and hold the control knob for the prime function to feed additional
pellets.
3. After you are finished priming the pellets into the burn pot, release the
control knob and the auger will stop feeding pellets.
TEMPERATURE
1. Push the control button to lock in the Temperature function.
2. Rotate the knob to select your desired Temperature.
3. Pushing the control button will now start the unit.
MEAT PROBE
The plug-in connection for the meat probe is on the left side
of the grill above the battery compartment. The meat probe
temperature will appear on the controller after the meat
probe is connected.
1. Push the control knob once to turn the unit ON. The controller
will flash several times and then turn to a solid screen. This lets
you know your unit is powered on.
2. Push the control knob again, this will take you to the function
screen where you can access the Temperature (F/C), Time, Meat
Probe Temperature, Prime, and Cleanout functions, as well as
the Battery level, AC adapter, Fan, Auger, Igniter, and Battery
removal indicators (when applicable.)
3. *Once you've turned the unit on by pushing the control
knob* Rotate the knob to select the Meat Probe function.
4. Push the button to lock in the Meat Probe function, then rotate
the control knob to the desired temperature you want your meat
probe set and push the button to set.
Note:
IMPORTANT TO NOTE:
• Disconnect the meat probe from the jack receptacle and cover
the port with the silicone cap when not in use.
• One meat probe is included with the unit.
• Use HALO brand meat probes only to prevent damage to the unit.
• The unit will go into WARM mode and the unit temperature will
reduce when the meat probe reaches the set temperature. This
will keep the food from continuing to cook before it is removed
from the unit.
DEGREES F/C
1. Rotate the knob to the F (Fahrenheit) or C (Celsius) function and
push the button to lock in this function.
2. Rotate the control knob to either F or C and push the control knob
to lock in your choice.
3. Please note the default setting is Fahrenheit.
TIME
1. Rotate the knob to select the Time function.
2. Push the button to lock in the Time function. You can set the
number of hours and minutes to time your smoke.
3. Rotate the control knob to the desired number of hours, then push
the control knob to confirm the hours.
4. Rotate the control knob to set the desired number of minutes,
then push the control knob to confirm the minutes.
5. The timer will count down to zero after your unit is started.
17
17
Publicidad
