Publicidad
Idiomas disponibles
Idiomas disponibles
Troubleshooting
Fault
Will not boot.
The device is not charging.
The device switches itself off at high temperatures.
The image is unclear.
The image has streaks.
The background is not uniform.
The image is too dark.
The image on the display is flat.
The computer does not recognize the device (internal
memory).
The time information on the images is incorrect.
Image quality is poor.
The detection range is too short.
The smartphone does not connect to my ZEISS DTI 6.
The WLAN signal is repeatedly lost or interrupted.
Personal data when you pass on or dispose of your ZEISS device
Remember that there may be personal photos and videos on the internal device
memory. Before passing on the device to a third party, please perform the factory
reset to delete this data and verify it has been deleted. By doing so, you help
maintain your privacy and data security.
Participating in IT security
Please take an active role in protecting the IT security of your device by using the
ZEISS Hunting App and installing new firmware updates as soon as they become
available.
Firmware update
A firmware update can be carried out using the ZEISS Hunting App. Follow the
instructions for this in the ZEISS Hunting App.
Note: Make sure that the device is fully charged before updating the firmware. Do
not switch off the device during the update, otherwise it may be damaged.
Note: If you initiate an update via the ZEISS Hunting App, you may need to confirm
this again on the device for security reasons.
ZEISS Hunting App
Install the ZEISS Hunting App on your smartphone and open the app. Follow the
steps shown there to connect to the ZEISS DTI 6.
The ZEISS Hunting App allows you to transfer images and videos to your
smartphone, view the live image, make settings and use other functions. A more
detailed description can be found in the help function of the app.
Note: To use the ZEISS Hunting App and its functions, ensure that your smartphone
is connected to the ZEISS DTI 6.
Note: Every time you connect to the ZEISS Hunting App, the current date and time
are automatically transferred from your smartphone to the device.
Note: Please note that you are not connected via the normal WLAN if you have
established a WLAN connection to your ZEISS DTI 6. To return to the normal WLAN,
disconnect your ZEISS DTI 6 from your smartphone.
USB port
Use the USB port (16) on the left side to charge your device or to transfer data
(photos and videos) to your PC.
The ZEISS DTI 6 functions as a mass storage device here.
Tripod thread
A 1/4-inch standard thread (15) for standard tripods is located on the bottom of the
device. Screw the device onto a tripod for more steady shooting.
* USB Type-C
and USB-C
are registered trademarks by the USB Implementers Forum.
®
®
Possible reasons
Battery is empty.
The USB cable is defective.
External power supply is not sufficient.
The USB cable is not properly connected to the device.
Automatic deactivation to protect the battery from
overheating.
The device must be recalibrated.
The screen brightness is set too low.
The contrast is set too low.
The device is not switched on.
The USB cable is not connected properly.
The required software has not been installed.
The time information (time/date) in the device is not
yet set.
Poor weather conditions may have adverse effects (e.g. heavy snowfall, rain, fog, etc.).
The WLAN password is incorrect.
There are too many WLAN networks in the immediate
vicinity of the device. There may be adverse effects.
The ZEISS DTI 6 is too far away or there are too many
other WLAN networks nearby.
There is an obstruction between the device and the
receiver.
Status LED
To set the LED display, select "Settings" in the main menu. Then navigate to
"Settings Device Menu". Briefly press the menu button (6) to open the submenu.
Navigate to "Status LED" and briefly press the menu button (6). Choose between
manual or disabled and confirm the selection by briefly pressing the menu
button (6). Press and hold the menu button (6) to return to observation mode.
In the "Manual" mode you can adjust the brightness level of the LED by means of
the App.
Note: To avoid fading in the dark, the brightness of the LED is kept low. The LED
may therefore sometimes be only barely visible in daylight.
Operating status Charge state
Normal
operating
condition
Standby mode
Off
All
Charging the device
Charge the device via the USB port (16) when the battery is empty. The battery
charge level of the device is shown in the lower right corner of the display. When the
charge level is low, the display changes to red. When the device is being charged,
the LED (3) lights up red when the device is switched on and off. When the battery is
fully charged, the LED (3) lights up green.
Only use chargers that meet the USB-C
Solution
Charge the device.
Replace the USB cable.
Check if the external power supply is fine.
This must be ensured by means of a USB-C
cable with a USB-C
PD (Power Delivery) power
®
supply.*
Unplug the USB cable and check that the connector
and port are undamaged and free from dirt.
Let the device cool down while switched off.
Follow the instructions when performing the
calibration procedure.
Adjust the screen brightness.
Adjust the contrast.
Transfer the images after turning on the power.
Please read the notes in the section
"USB port".
Install the software required for your system.
Follow the instructions to set the time information.
Enter the correct password.
Move the device to a location with few or no direct
WLAN networks.
Change the location of the device so that a WLAN
signal is detected directly.
Does not charge
Does not charge (low charge
level)
Charging
Charging (fully charged)
Charging power too low
Does not charge
Does not charge (low charge
level)
Charging
Charging (fully charged)
Charging power too low
Does not charge
Charging
Charging (fully charged)
Charging power too low
No battery inserted
and USB Power Delivery specification.
®
to USB-C
®
®
LED color
LED status
Green
Constant
Red
Flashing
Red
Constant
Green
Constant
Blue
Flashing
Green
Flashing
Red
Flashing
Red
Constant
Green
Constant
Blue
Flashing
-
-
Red
Constant
Green
Constant
Blue
Flashing
Blue
Constant
*
13 | 100 EN
Publicidad
