Luna AIWC 1 THL Manual Del Usuario página 12

• Do not wear loose long hair, loose clothing or jewellery, which could become caught up in
moving parts of the tool and cause injuries and clothing damages.
• A switched-on tool may be directed towards the work material only. Loose parts may disunite
and cause damages. A person or an object may become in contact with the tool, which could
cause an accident or material loses.
• Cold or wet hands, smoking and snivel may increase vibration caused hazards.
• Let the tool operate and by holding the handle use the least possible force. If possible, the tool
should be supported on a stable support block.
• Interruption of work should be ensured or another kind of work, not involving use of vibra-
ting tools should be alternatively performed, in order to reduce the harmful influence caused
by the vibration.
• Ensure that the workplace is well lit.
Important information
Tools must be lubricated
Before use always lubricate the tool with a few drops of oil AIRTOIL 22 (Luna 15531-0105)
intended for use with pneumatic tools, by dropping it into the air inlet opening of the tool. In
case of continuous work, a pneumatic lubrication system (Luna 20571-0106) should be used,
adjusted to about two drops per minute. If the tool is not used for a longer period of time, it is
required to drop a few drops of oil before storage of the tool, in order to reduce the corrosion
risk.
Attention! Use only oil that is supposed for pneumatic tools. Use of other oils may result in
"clumping" of oil and reduction of the movement ability of the machine. It may cause reduced
work efficiency.
Leakages must be avoided
Avoid leakages in the air circulation system. Always use a thread sealing tape at the point where
the plug is connected to the tool. Pay attention that hoses and hose clamps are in good conditions.
The compressed air must be dry
As cleaner and dryer the compressed air is, the longer is life time of the tool. In order to ensure
it, we recommend use of air filter, which removes water from the compressed air, accordingly
reducing eventual damages of the tool and connections caused by corrosion. Remember to
remove eventual water condensate from the compressor tank and the compressed air supply
system before each working day.
Remember!
24
• Under no circumstances a defective impact wrench or sockets can be used as it may cause
injuries and material loses.
• Dismantle the plastic plug from the air inlet (Pos.5) and assemble a nipple 1/2" outlet thread.
• During assembly or dismantling sockets, the impact wrench must always be disconnected
from the compressed air supply. It will help you to secure yourself against unintentional
pressing of the switch (Pos.6) and start-up of rotation of the anvil (Pos.1) which can cause
injuries.
• Make sure that before start-up of the tool the respective socket is properly secured in the anvil
(Pos.1) by attached locking pins and pin stoppers. Remember that use of no other sockets then
impact sockets must be used, as inappropriate socket may loosen from fixation and disunite
from the tool. Never run the machine in idle running. The socket may come loose and cause
injuries or material damages.
• Always use the support handle (Pos.2), in order to ensure easy and safe operation of the tool.
• Change of the rotation direction, should be performed by regulator (Pos.4), while the anvil
does not rotate.
• Check air pressure and, if necessary, adjust it so that the tool would operate at the required
pressure and torque. Adjustment of the pressure is performed by use of the compressor or
separately installed pressure regulator and adjustment of the torque is performed by use of the
torque regulator (Pos.7). Specification of the tool complies with a 6.2 bar pressure.
• Always be careful when using the impact wrench. A negligent attitude towards the tool may
cause damages of the internal parts and housing fractures. It may result in reduction of the
tool efficiency and the tool may loose its value.
Maintenance: Lubricating is important in order to reduce noise and vibration level. In case of
continuous use of the tool is should be cleaned and checked at least 2 times a year.
Instructions
25