Publicidad
MESURES DE PRÉCAUTION
IMPORTANT:
Si la trappe de succion ou le boyau se BLOQUENT, éteignez
l'aspirateur et retirez l'obstacle avant de redémarrer l'appareil.
1.
N'approchez pas l'aspirateur
trop près des éléments
chauffants ou des radiateurs.
2. Avant d'insérer la fiche d'alimentation
dans la prise murale, assurez-vous
que vos mains sont sèches.
3. N'aspirez aucun liquide.
4.
Tenez toutes les parties du corps,
les doigts, les cheveux et les
vêtements lâches éloignés des
ouvertures, du batteur rotatif et des
autres pièces mobiles.
5.
Lorsque vous retirez le cordon
d'alimentation de la prise
murale, tirez sur la fiche et non
pas sur le cordon.
6.
Ne ramassez aucun objet fumant
ou brûlant tels que les cigarettes,
allumettes ou cendres chaudes.
7.
Évitez de faire passer l'aspirateur
sur le cordon d'alimentation.
8.
N'utilisez pas l'aspirateur sans
sa coupelle ou sans ses filtres.
9.
Avant de commencer à nettoyer,
assurez-vous de retirer tout gros
objet ou tout objet coupant
pouvant endommager
l'aspirateur.
30
PROBLEM SOLVING
This appliance was inspected thoroughly and was in good operating condition when it
was shipped from the factory. If a minor problem occurs, it usually can be solved quite
easily when the cause is found. Therefore, this checklist is provided for your
convenience.
PROBLEM
POSSIBLE CAUSE
1.
Not properly plugged into
wall outlet.
Cleaner Won't
2.
No electricity in wall outlet.
3.
On/Off switch not turned on.
Run
4.
Motor thermostat tripped.
5.
Blown fuse/tripped breaker.
1.
Full or clogged dust cup.
2.
Wrong pile height setting.
3.
Clogged nozzle.
4.
Clogged dust inlet port.
5.
Clogged hose.
Cleaner Won't
6.
Broken belt.
Pick Up
7.
Hose not inserted fully.
8.
Dirty filters.
9.
HEPA filter needs cleaning
or replacing.
10. HEPA filter frame needs
cleaning.
Cleaner Picks
Up Moveable
Rugs Or
1.
Wrong pile height setting.
Pushes Too
Hard
Agitator Does
1.
Broken belt.
Not Turn
2.
Belt installed incorrectly.
1.
Rotating brush, turbine or
Pet Hair Power
elbow obstructed.
Brush Does Not
2.
Belt broken.
Rotate Or
3.
Hose obstructed.
Rotates Slowly
4.
HEPA filter clogged.
1.
Attachment use restricts air
Air Flow
flow.
Restricted With
2.
New carpet debris clogging
Attachment Use
air path.
POSSIBLE SOLUTION
1.
Plug in firmly.
2.
Check fuse or breaker.
3.
Push on/off switch to on
4.
Reset motor thermostat.
5.
Reset circuit breaker or replace fuse.
1.
Clean dust cup.
2.
Adjust setting.
3.
Remove obstruction.
4.
Remove power head cover and
remove obstruction.
5.
Remove obstruction.
6.
Replace belt.
7.
Push hose in securely.
8.
Clean / change filters.
9.
Clean or replace HEPA filter.
10. Clean HEPA filter frame.
1.
Adjust setting.
1.
Replace belt.
2.
Check belt changing and agitator
cleaning.
1.
Clear obstructions.
2.
Call Customer Service.
3.
Clear obstruction.
4.
Clean HEPA filter.
1.
Check attachment.
2.
Remove obstruction.
11
Publicidad
