Roadstar HRA-1520MP Manual De Instrucciones página 5

CD/MP3 OPERATION
Loading and Unloading Compact Discs
1. Set the Function Selector (12) to the CD/MP3 Position.
2. Open the CD Door (15).
3. When the door has opened, remove a disc from its case and place it carefully in the
compartment with the label side facing up. Locate 3" discs, on the central spindle in the
compartment.
PLAY BACK
1. Load a CD into the disc compartment, and close the compartment.
2. Press the Play/Pause button (7). The Play/Pause indicator will light up and disc play will
begin from the start of the first track of the disc.
3. At the end of the disc, the unit will switch to stop mode and the play indicator will go out.
Notes: If the disc is deeply scratched, or too dirty, disc play may not start.
If an improperly centred disc is played, noise can be heard in the mechanism. The
use of such discs should be avoided.
IMPORTANT INFORMATION
This compact disc player has built-in error compensation circuits to correct for minor defects
in a disc. There are limits, however, to the amount of correction available.
In some cases the CD player may skip some tracks on a disc during disc play. This problem
may be caused by defects (such as scratches) on the disc being played, which are too large
for the error compensation circuits to handle.
4. To stop CD play. Press the Stop Button (5). Disc play will stop, the Play indicator will go
off, and the display will show the total number of tracks on the CD.
5. To temporarily stop disc play (pause mode), press the Pause Button (7). Disc play will
stop at the current play position. The track number indicator will begin to flash.
6. To resume disc play, press the Play Button again. The Play indicator will light up.
Starting disc play from the beginning of a particular track
• Press the Forward or Reverse Skip Track Buttons (9) to select the desired track. The
number of the selected track will be shown on the CD display (4). Press the Play/Pause
Button (7) to start play.
To skip to the next track
1. To skip to the beginning of next track 5 while track 4 is playing.
2. Press the Skip Forward (10) Skip Track Button once to skip to the beginning of next track.
English 5
To skip back to the previous track on a disc
1. To skip back to the beginning of current track. Press the skip Backward (9) once.
2
Continuously pressing the Reverse (9) Skip Track Button makes the CD player skip back
through the disc track by track. Once the beginning of the first track is reached, the CD player
will not go back any further.
Manual Search
•
•
PROGRAMMED DISC PLAY
It is not possible to enter programs during disc play. Press the Stop button (6) first, then follow
the instructions below.
Press the PROGRAM button (3). "001" will flash on the LED display and the Program
Indicator (8) will light up.
Press the Forward and Reverse Skip Track buttons to select the track to be stored in
position1.
Press the PROGRAM button (3). The first program selection is now stored in the program
memory 1.
Select the next track to be programmed using the Forward and Reverse Skip Track (10/9)
buttons. Press the PROGRAM button (3) to store this track.
Continue entering tracks in this way until all the desired tracks are stored (up to a limit of 20).
When the PROGRAM button (3) is pressed to store the 20th track, the display will return
to the 1st program location. Press the PROGRAM button (3) to step through the program
locations.
6 English
Continuously pressing the Forward Skip Track Button until the desired trade is reached.
Once the beginning of the last track is reached the CD player will not advance any
further.
Toskip back to the beginning of previous track.
Press the skip backward (9) Skip Track Button twice.
During playback, pressing the Forward or Reverse Skip / Search buttons will cause the
player to scan through the current track. At the end of a track the player will skip to the
next track and continue scanning. At the beginning of a track the player will skip to the
previous track and continue scanning.
When the player reaches the end of the final track, or the beginning of the first track, it will
stop scanning.