voestalpine bohler SABER 70 CHP Manual De Instrucciones página 43

Cause Insufficient air pressure.
Solution Adjust the gas flow.
Read the paragraph "Installation".
Slag inclusions
Cause Poor cleanliness.
Solution Clean the pieces accurately before welding/cutting.
Cause Electrode diameter too big.
Solution Use a smaller diameter electrode.
Cause Incorrect edge preparation.
Solution Increase the chamfering.
Cause Incorrect welding/cutting mode.
Solution Decrease the distance between the electrode and
the piece.
Move regularly during all the welding/cutting
operations.
Tungsten inclusions
Cause Incorrect welding/cutting parameters.
Solution Decrease the welding/cutting voltage.
Use a bigger diameter electrode.
Cause Incorrect electrode.
Solution Always use quality materials and products.
Sharpen the electrode carefully.
Cause Incorrect welding/cutting mode.
Solution Avoid contact between the electrode and the weld
pool.
Blowholes
Cause Insufficient shielding gas.
Solution Adjust the gas flow.
Check that the diffuser and the gas nozzle of the
torch are in good condition.
Sticking
Cause Incorrect arc length.
Solution Increase the distance between the electrode and
the piece.
Increase the welding/cutting voltage.
Cause Incorrect welding/cutting parameters.
Solution Increase the welding/cutting current.
Cause Incorrect welding/cutting mode.
Solution Angle the torch more.
Cause Pieces to be welded/cut too big.
Solution Increase the welding/cutting current.
Increase the welding /cutting voltage.
Cause Incorrect arc regulation.
Solution Increase the equivalent circuit inductive value setting.
Use a higher setting inductive connection.
Undercuts
Cause Incorrect welding/cutting parameters.
Solution Decrease the welding/cutting voltage.
Use a smaller diameter electrode.
Cause Incorrect arc length.
Solution Increase the distance between the electrode and
the piece.
Increase the welding/cutting voltage.
Cause Incorrect welding/cutting mode.
Solution Decrease the side oscillation speed while filling.
Decrease the travel speed while welding/cutting.
Cause Insufficient shielding gas.
Solution Use gases suitable for the materials to be welded/
cut.
Oxidations
Cause Insufficient gas protection.
Solution Adjust the gas flow.
Check that the diffuser and the gas nozzle of the
torch are in good condition.
Porosity
Cause Grease, varnish, rust or dirt on the workpieces to
be welded/cut.
Solution Clean the workpieces carefully before welding/cut-
ting.
Cause Grease, varnish, rust or dirt on the filler material.
Solution Always use quality materials and products.
Keep the filler metal always in perfect condition.
Cause Humidity in the filler metal.
Solution Always use quality materials and products.
Keep the filler metal always in perfect condition.
Cause Incorrect arc length.
Solution Decrease the distance between the electrode and
the piece.
Decrease the welding/cutting voltage.
Cause Humidity in the welding/cutting gas.
Solution Always use quality materials and products.
Ensure the gas supply system is always in perfect
condition.
Cause Insufficient shielding gas.
Solution Adjust the gas flow.
Check that the diffuser and the gas nozzle of the
torch are in good condition.
Cause The weld pool solidifies too quickly.
Solution Decrease the travel speed while welding/cutting.
Pre-heat the workpieces to be welded/cut.
Increase the welding/cutting current.
Hot cracks
Cause Incorrect welding/cutting parameters.
Solution Decrease the welding/cutting voltage.
Use a smaller diameter electrode.
Cause Grease, varnish, rust or dirt on the workpieces to
be welded/cut.
Solution Clean the workpieces carefully before welding/cut-
ting.
Cause Grease, varnish, rust or dirt on the filler metal.
Solution Always use quality materials and products.
Keep the filler metal always in perfect condition.
Cause Incorrect welding/cutting mode.
Solution Carry out the correct sequence of operations for
the type of joint to be welded/cut.
43