Publicidad
Idiomas disponibles
Idiomas disponibles
modulation mode has to correspond to the one of your correspondent.
Amplitude Modulation / AM: communication on a field with relief and
-
obstacles at middle distance (the most used).
Frequency Modulation / FM: for nearby communications on a flat open
-
field.
In U configuration only: in FM mode, a short press on the MODE key (5)
alternates
between the ENG or CEPT frequency bands. "UK" is displayed
when the ENG frequency band is selected (see table on page 80).
PA (Public Address)
(long press)
An external loudspeaker can be connected to the unit by the PA jack plug
located on the back panel PA.SP. (D). Turn the VOL knob (1) to adjust the
PA volume.
Long press MODE key (5) to
alternate
PA
For details on operating in
53.
M1
See § MEMORY page 47.
6) MEMORY ~ CTCSS/DCS ~ M2
MEMORY
(short press)
This CB radio allows you to
memorize
To store into memory:
-
Select the channel and its attributes.
-
Press the MEM key (6) for one second. If the KEY BEEP function is active, a
beep sounds. "MEM" flashes.
Press for one second one of the keys M1 (5), M2 (6), M3 (7) or M4 (8) to
-
memorize. "MEM" appears in the display and the number of the selected
memory (M1, M2, M3 or M4) flashes.
-
If the KEY BEEP function is active, a long beep confirms the success of the
operation.
To call a memory:
Press the MEM key (6) for one second. If the KEY BEEP function is active, a
-
beep sounds. "MEM" flashes.
-
Briefly press one of the M1 (5), M2 (6), M3 (7) or M4 (8) keys to display the
selected memory.
-
"MEM" is displayed, the number of the selected memory (M1, M2, M3 or
M4) flashes.
CB
PA
between
and
mode.
mode, consult the PA SETTING menu page
4 channels with the following attributes.
CTCSS/DCS
For simplicity, in this manual we will speak of CTCSS/DCS code to indicate
both a CTCSS tone and a DCS code, of GENRE to indicate the kind of code
(CTCSS, DCS or OFF = no code). TYPE indicates whether this is a TX transmis-
sion or an RX reception and MODE specifies the operating mode, Identical
I d or different DF.
Consult the CODE SET menu page 54.
See list of codes on pages 83.
Note: Codes can only be used in FM. Each channel can have its own code.
-
Press for one second one of the MEM key (6) to
CTCSS/DCS function.
Activation
If a CTCSS/DCS code has been stored, it becomes active, "CTCSS" or "DCS"
icon is displayed on the screen.
In MODE I d, if no CTCSS/DCS code has been stored, the device emits an
error beep. Go to the CODE SET menu to store a CTCSS/DCS code.
In DF MODE, if no CTCSS/DCS code has been stored in either TYPE TX or TYPE
RX, the device emits an error beep. Go to the CODE SET menu to store the
CTCSS/DCS codes.
Deactivation
If a CTCSS/DCS code has been stored and "CTCSS" or "DCS" is displayed on
the screen, a long press on the MEM key (6) deactivates the stored code,
"CTCSS" or "DCS" disappears, a deactivation beep sounds. The memorized
CTCSS/DCS code is kept in memory but no longer functions.
M2
See § MEMORY page 47.
7) SCAN ~ DW ~ SKIP ~ M3
SCAN
(short press)
Press the SCAN/DW key (7) to
order. "SCAN" is displayed. The scanning stops as a channel is active. The
scanning automatically starts 3 seconds after the end of the transmission
and no key is activated. In
or use the UP/DN buttons (19) on the microphone to change scan direction.
(see § SKIP below)
Press the PTT switch (18) or the SCAN key (7) to
47
activate/deactivate
activate
the SCAN function in ascending
mode, turn the rotary CH knob (4)
SCANNING
exit
the SCAN function.
the
Publicidad
