Publicidad
Idiomas disponibles
Idiomas disponibles
to
select
the code (01 to 38 for CTCSS 001 to 104 for DCS).
10. Press PUSH key (4) to
confirm
the selected code. The unit returns to point 5,
to set the second type.
11. If you don't need to set the second type, long press the PUSH key (4) to
validate
and exit the MENU.
12. If no key is pressed, the device
saving
the changes.
The default mode is I d (Identical). The default genre is OFF.
See the RESET menu.
15) EMERGENCY CHANNEL
Long Press PUSH key (4) to
enter
1.
Turn the CH rotary knob (4) or use the UP/DN keys (19) on the microphone
to
select
the EMG SETTING EMG 1 menu.
2.
Press PUSH key (4), turn the CH knob (4) or use the UP/DN keys (19) on the
select
microphone to
the priority channel to set EMG 1 or EMG 2.
3.
Press PUSH key (4). The channel flashes in the display.
4.
Turn CH knob (4) or use the UP/DN keys (19) on the microphone to select
the channel.
5.
Press MODE (5) to
select
AM, FM or UK (U configuration only), USB and LSB
mode.
6.
Press PUSH key (4) again to
confirm.
again at point 1 to
set
another function or b) Press the PTT switch (18) to
exit
MENU.
7.
exits
If no key is pressed, the unit
from the display.
Default Emergency channel 1 is 9 in AM.
Default Emergency channel 2 is 19 in AM.
See § EMERGENCY CHANNELS page 48.
16) DW (DUAL WATCH)
This function allows you to customize the second channel scanned by the
DUAL WATCH function.
Long Press PUSH key (4) to
enter
1.
Turn the CH rotary knob (4) or use the UP/DN keys (19) on the microphone
to
select
the DW SET menu.
2.
Press the PUSH key (4). The channel flashes in the display.
3.
Turn CH knob (4) or use the UP/DN keys (19) on the microphone to select
the channel.
exits
the MENU after 10 seconds without
the MENU.
is displayed.
The channel stops flashing. a) Start
the MENU after 10 seconds.
disappears
the MENU.
is displayed.
4.
Press MODE (5) to
select
AM, FM or UK (U configuration only), USB and LSB
mode.
5.
Press PUSH key (4) again to
again at point 1 to
set
another function or b) Press the PTT switch (18) to
exit
MENU
6.
If no key is pressed, the unit
from the display.
17) REPEATER / RELAY setting
WARNING! This function is valid only on the D frequency band. See the
configuration table page 84.
This function allows you to
The radio receives on the current channel RX1 and transmits on the selected
channel TX2.
1.
Select the RX1 channel.
2.
Long Press PUSH key (4) to
3.
Turn the CH rotary knob (4) or use the UP/DN keys (19) on the microphone
to
select
the RPTX SETTING menu.
4.
Short press on the PUSH key (4). The current transmission channel TX2 blinks
on the display.
5.
Turn the CH rotary knob (4) or use UP/DN keys (19) on the microphone to
select
the transmission channel (TX2) or I d (identical, no repeater).
6.
New press on the PUSH key (4) to validate. a) Return to the point 1 to set
another menu or b) Short press the PTT key (18) to
MENU.
disappears from the display.
7.
If no key is pressed, the unit
from the display.
The default transmission channel is 1d (identical RX channel).
To activate the function, see the § REPEATER/RELAY page 49.
18) SPAN SETTING
When the function is active, the frequency can be adjusted continuously.
Pressing the PUSH knob (4) displays a bar under the first or second decimal
55
confirm.
The channel stops flashing. a) Start
exits
the MENU after 10 seconds.
increase
the range of your CB by using relays.
enter
the MENU.
is displayed.
validate
exits
MENU after 10 seconds.
disappears
exit
and
the
disappears
Publicidad
