Sound Adjustments; Front Speaker Output Balance - JVC RX-DV31SL Manual De Instrucciones

Sound Adjustments

You can make sound adjustments to your preference after
completing basic setting.
Adjustment items:

• Front speaker output balance*

1
• Tone*
• Speaker output levels* 1
• DAP effect level
• Subwoofer audio position
1
You can also make these adjustments using the Choice menu (see
*
pages 53 to 58).
Note:
• Adjustments you made are memorized separately for each source.
7 Operation buttons
On the front panel ONLY*
Button
ADJUST Show the adjustable items on the
3
display*
CONTROL 5/∞
Select an item on the display.
Each time you press the button, the
adjustable items change (see
"Configuration of the items on the
display" below).
CONTROL 3/2
Adjust the selected item.
• When no operation is done for about 5 seconds, the
indications on the display will disappear.
2 You can also make sound adjustment except for front
*
speakers' output balance from the remote control.
3 Pressing ADJUST repeatedly also changes the items.
*
Configuration of the items on the display
BAL
BASS
(Balance)
4
SUBWFR * CENTER *
(Subwoofer)
4
SURR R * EFFECT *
(Surround right)
(back to the beginning)
4
* These items appear only when the corresponding
speakers are set to other than "NONE" as its speaker size.
* 5 "EFFECT" appears only when one of DAP modes (see
pages 30 and 31) is activated.
* 6 "AUDIO POS" appears only when "YES" or "USE" (see
pages 23, 25, or 57) is selected for the subwoofer.
1
2
To do
.
TREBLE
4 4
SURR L *
(Surround left)
5 6
AUDIO POS *
(Audio position)
7 Operating procedure
Ex.: When setting the front speaker output balance.
Before you start, remember...
There is a time limit in doing the following steps.
If the setting is canceled before you finish, start from step 1
again.
1
Press ADJUST.
The CONTROL buttons now work for sound adjustments.
The setting item selected previously appears on the
display.
2 Press CONTROL ∞ (or 5) repeatedly until
"BAL (Balance)" (with the current setting)
appears on the display.
PROGRAM
ANALOG DIGITAL AUTO PL DSP SLEEP REPEAT
PPCM AUTO SURROUND
GROUP TITLE TRACK CHAP. RESUME
L C R
DIGITAL
LPCM SUBWFR LFE
MPEG-2 AAC LS S RS
3
Press CONTROL 3 (or 2) to adjust the front
speaker balance.
• Each time you press the button, the indication changes
as follows:
ANALOG DIGITAL AUTO PL DSP SLEEP PROGRAM REPEAT
PPCM AUTO SURROUND
GROUP TITLE TRACK CHAP. RESUME
L C R
DIGITAL
LPCM SUBWFR LFE
MPEG-2 AAC LS S RS
R –21 CENTER
4
Repeat steps 2 and 3 to set other items if
necessary.
• For details about each item, see below.
7 Front speaker output balance
"BAL (balance)"
ANALOG DIGITAL AUTO PL DSP SLEEP PROGRAM REPEAT
PPCM AUTO SURROUND
GROUP TITLE TRACK CHAP. RESUME
L C R
DIGITAL
SUBWFR LFE
LPCM
MPEG-2 AAC LS S RS
If the sounds you hear from the front right and left speakers
are unequal, you can adjust the speaker output balance.
Adjust the output balance appropriately from the listening
point within the range of R (Right) –21 to CENTER (0) or
CENTER (0) to L (Left) –21 ("CENTER" is the initial setting).
Note:
• When you select "R –21," no sound comes out of the front right
speaker, and when you select "L –21," no sound comes out of the
front left speaker.
1A-B RANDOM PROGRESSIVE RDS TA NEWS INFO INPUT ATT
SPK 1 2 REC
AUTO MODE
B.S.P BONUS TUNED STEREO AUTO MUTING
A.POSITION
kHz
MHz
VOL
1A-B RANDOM PROGRESSIVE RDS TA NEWS INFO INPUT ATT
REC
SPK 1 2
AUTO MODE
B.S.P BONUS TUNED STEREO AUTO MUTING
A.POSITION
kHz
MHz
VOL
L –21
1A-B RANDOM PROGRESSIVE RDS TA NEWS INFO INPUT ATT
SPK 1 2 REC
AUTO MODE
B.S.P BONUS TUNED STEREO AUTO MUTING
A.POSITION
kHz
MHz
VOL
28