Catit Pixi Manual Del Usuario página 16

EN
CONTROLS, INSTRUCTIONS & TROUBLESHOOTING
PLEASE VISIT HTTPS://WWW.CATIT.COM/HELP-ADVICE/ FOR THE LATEST INFORMATION AND GUIDES.
CONTROLS / AUDIO
Touch Touch
Controls Controls
Unlock
Lock
Signals with Blue - continuous
Blue LED
Blue - blinking fast
Blue - steady blue for
5 seconds + 2 short beeps
Blue - blinking slow
(with USB-c cable inserted)
Blue - continuous
(with USB-c cable inserted)
Signals with Red - continuous
Red LED
Red - steady red for
5 seconds + 3 long beeps
Red - blinking 5 times + beep
5 times, every 6 minutes
Red - blinking fast
DEVICE MODES
OFF OFF
The device is completely powered off.
but the device will no longer automatically monitor and restore the vacuum periodically.
ON - Sleep ON - Sleep After 80 seconds of inactivity, the Catit
save power. In this mode, the device will automatically monitor and restore the vacuum every 3
hours as needed.
ON - Awake ON - Awake
The device is turned on and ready to create/release the vacuum.
30
• Turn ON the device
• Release the vacuum to open the container
• Wake the device
• Turn OFF the device
• Create a vacuum
• Wake the device
Battery level is above 15% (when the device is not in sleep mode)
Creating vacuum / releasing vacuum
Vacuum seal successful / Vacuum released successfully
Battery is charging
Battery is fully charged
Low battery (below 15%) (when the device is not in sleep mode)
Vacuum seal unsuccessful
Low battery alert (less than 15%) when in sleep mode
Creating vacuum / releasing vacuum (while battery is below 15%)
Turning off the device will not release an existing vacuum seal,
PIXI Smart Vacuum Food container will go to sleep to
® ®
INSTRUCTIONS
Turn ON device: Press and hold the Unlock button for 5 seconds. If successful, you'll hear a short beep and see
5 s
the blue LED light shines for 60 seconds.
Wake device from sleep mode: Touch any button on the device for 1 second to wake it from sleep mode.
1 s
If successful, the blue LED will light up for 3 seconds, with a short beep. The device will be in standby for 80
seconds before returning to sleep mode.
Turn OFF device: First wake the device by pressing any button for 1 second. Next, press and hold the Lock
5 s
button for 5 seconds. The device will turn off with a long beep for confirmation.
Create vacuum seal: Ensure the device is awake. Briefly press the lock button (up to 1 second) and gently push
1 s
down on the lid for ± 5 seconds to help ensure a successful vacuum seal. The blue LED will blink quickly while
the vacuum is created. When the process is finished, the blue LED will light up for 5 seconds along with 2 short
beeps. If unsuccessful, the LED will be red for 5 seconds with 3 long beeps.
Release vacuum seal: Ensure the device is awake. Briefly press the Unlock button (up to 1 second). The blue
1 s
LED will blink quickly while the vacuum is released. When the process is finished, the blue LED will light up for 5
seconds along with 2 short beeps.
TROUBLESHOOTING
Problem Possible solution / effect
The Catit PIXI Smart Vacuum Food Make sure the device is turned on. Wake the device before trying to op-
® ®
Container is unresponsive erate it. Also ensure to press (and hold) the correct button for as long
as described in the instructions. The timing needs to be accurate.
My device won't recharge Check if you have a working USB-C cable and USB-A adaptor (5V, min.
1A)
The vacuum seal was not intact upon Ensure the rubber sealing ring of the top lid and the rim of the container are
opening the food reservoir clean and free of debris or food particles, as these may prevent the device
from creating a vacuum seal.The Catit
needs to be operational (awake or in sleep mode) for it to check and restore
the vacuum every 3 hours.
PIXI Smart Vacuum Food Container
® ®
31