Publicidad
Idiomas disponibles
Idiomas disponibles
Sound power level LwA
Sound pressure level L
pA
Uncertainty K
wA/pA
7.
Before commissioning
• Before connecting the machine, make certain that
the data on the type plate matches with the mains
power data.
• Prior to initial commissioning, remove the transport
plug (B) and fill the compressor pump housing with
oil as described in item 8.4.
• Check the device for transport damage. Report
any damage immediately to the transport company
which was used to deliver the compressor.
• Install the compressor near the point of consump-
tion.
• Avoid long air lines and supply lines (extension ca-
bles).
• Make sure that the intake air is dry and free of dust.
• Do not deploy the compressor in damp or wet areas.
• Operate the compressor only in suitable areas (well
ventilated, ambient temperature +5°C to 40°C).
There must be no dust, acids, vapours, explosive
gases or inflammable gases in the room.
• The compressor is designed to be used in dry
rooms. It is prohibited to use the compressor in are-
as where work is conducted with sprayed water.
• The oil level in the compressor pump must be
checked before commissioning.
• The compressor may only be used outdoor briefly
when the ambient conditions are dry.
• The compressor must always be kept dry and must
not be left outdoors after work is complete.
8. Attachment and operation
Attention!
Always make sure the device is fully assembled before
commissioning!
You require the following for assembly:
• 2 x open-ended spanner, 17 mm (not included in the
scope of delivery)
• 2 x open-ended spanner 14 mm (not included in the
scope of delivery)
8.1 Installing the wheels (Fig. 5)
• Fit the wheels (11) provided as shown.
97 dB(A)
8.2 Installing the foot (2x) (Fig. 6)
• Fit the feet (2x) provided as shown in.
71 dB(A)
2.03 dB(A)
8.3 Installing the air filter (2x) (Fig. 7, 8)
• Remove the transport plug (A) and screw the air
filter (14) to the device.
8.4 Replacing the transport lid (B)
(Fig. 9, 10)
• Remove the transport lid (A) of the oil filler hole (18).
• Fill the compressor oil supplied into the compressor
pump housing and fit the enclosed oil plug (15) into
the oil filler hole (18).
8.5 Mains power connection
• The compressor is equipped with a mains cable with
protective contact plug. This can be connected to
any mains socket 230 V~ 50 Hz with an earth con-
tact and that is protected at 16 A.
• Before commissioning, ensure that the mains volt-
age matches with the operating voltage and the ma-
chine's power rating on the type plate.
• Long supply cables, extensions, cable reels, etc.
cause a drop in voltage and can impede motor
start-up.
• In the case of temperatures below +5°C, motor
starting can be endangered by sluggishness.
8.6 ON/OFF switch (Fig. 2)
• Pull the ON/OFF switch (16) upwards to switch on
the compressor. Press the ON/OFF switch down
to switch off.
8.7 Pressure adjustment: (Fig. 1, 3)
• The pressure at the manometer (4) is adjusted with
the pressure regulator (5).
• The pressure set can be utilised by connecting to
the quick-coupling (3).
• The boiler pressure is read off at the manometer (6).
• The boiler pressure is taken at the quick-coupling
(7).
8.8 Pressure switch setting (Fig. 1)
• The pressure switch (2) is set at the factory.
Switch-on pressure ca. 6 bar
Switch-off pressure ca. 8 bar
8.9 Thermal protection switch
The thermal protector is built into the device.
If the thermal protector has tripped, proceed as follows:
• Pull out the mains plug.
www.scheppach.com
GB | 25
Publicidad
