Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
ENGLISH
Getting Started
Getting Started
Introduction
Introduction
This manual provides operation instructions and information required to
operate the SmartWeight Pro
/ HN
®
familiar with the contents of this manual prior to operating the SmartWeight
Pro
Balancer.
®
The owner of the SmartWeight Pro
responsible for arranging technical training. The SmartWeight Pro
/ Elite
Balancers are to be operated only by qualified trained technicians.
®
Maintaining records of personnel trained is solely the responsibility of the
owner and management.
This manual assumes the technician has already been trained in basic
balancing procedures.
Corporate Information
Hunter Engineering Company
Web: www.hunter.com
For Your Safety
For Your Safety
Hazard Definitions
Watch for these symbols:
CAUTION: Hazards or unsafe practices, which could result in
minor personal injury or product or property damage.
WARNING: Hazards or unsafe practices, which could result
in severe personal injury or death.
These symbols identify situations that could be detrimental to your safety and/
or cause equipment damage.
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before operating the SmartWeight Pro
Balancers. Read and follow the instructions and warnings provided in the
service, operation and specification documents of the products with which
this SmartWeight Pro
/ HN
/ Elite
®
®
manufacturers, tire manufacturers etc.).
Do not operate equipment with a damaged cord or equipment that has been
dropped or damaged until a Hunter Service Representative has examined it.
Always unplug equipment from electrical outlet when not in use. Never use
the cord to pull the plug from the outlet. Grasp plug and pull to disconnect.
If an extension cord is necessary, a cord with a current rating equal to or more
than that of the equipment should be used. Cords rated for less current than
the equipment may overheat. Care should be taken to arrange the cord so
that it will not be tripped over or pulled.
Verify that the electrical supply circuit and the receptacle are properly
grounded.
To reduce the risk of electrical shock, do not use on wet surfaces or expose
to rain.
Verify the appropriate electrical supply circuit is the same voltage and
amperage ratings as marked on the balancer before operating.
DO NOT ALTER THE ELECTRICAL PLUG. Plugging the
electrical plug into an unsuitable supply circuit will damage
the equipment and may result in personal injury..
To reduce the risk of fire, do not operate equipment near open containers of
flammable liquids (gasoline).
Read and follow all caution and warning labels affixed to your equipment and
tools. Misuse of this equipment can cause personal injury and shorten the life
of the balancer.
Keep all instructions permanently with the unit.
Keep all decals, labels, and notices clean and visible.
To prevent accidents and/or damage to the balancer, use only Hunter
SmartWeight Pro
and SmartWeight HN
®
accessories.
Use equipment only as described in this manual.
Never stand on the balancer.
Wear non-slip safety footwear when operating the balancer.
Keep hair, loose clothing, neckties, jewelry, fingers, and all parts of body away
from all moving parts.
Do not place any tools, weights, or other objects on the safety hood while
operating the balancer.
ALWAYS WEAR OSHA APPROVED SAFETY GLASSES. Eyeglasses that
have only impact resistant lenses are NOT safety glasses.
English
/ Elite
Balancers. Read and become
®
®
/ HN
/ Elite
Balancers is solely
®
®
®
/ HN
®
/ HN
/ Elite
®
®
Balancers are used (i.e., automobile
®
Balancers recommended
®
Keep the safety hood and its safety interlock system in good working order.
Verify that the wheel is mounted properly and that the wing nut is firmly
tightened before spinning the wheel.
The safety hood must be closed before selecting the green "START" button,
to spin the wheel.
Hood Autostart will cause the balancer shaft to spin automatically upon hood
closure. For the next Autostart, the safety hood has to be lifted to the full up
position and then closed.
Raise safety hood only after wheel has come to a complete stop. If safety
hood is raised before the spin is completed, the weight values will not be
displayed.
Do not let cord hang over any edge or contact fan blades or hot manifolds.
The red "STOP" button, can be used for emergency stops.
®
Never reach under the hood while the balancer is
performing a balance spin.
SAVE THESE INSTRUCTIONS
Electrical
The Hunter SmartWeight Pro
manufactured to operate at a specific voltage and amperage rating.
Make sure that the appropriate electrical supply circuit is of the same voltage
and amperage ratings as marked on the balancer.
DO NOT ALTER THE ELECTRICAL PLUG. Plugging the
electrical plug into an unsuitable supply circuit will damage
the equipment.
Make sure that the electrical supply circuit and the appropriate receptacle is
installed with proper grounding.
To prevent the possibility of electrical shock injury or damage to the
equipment when servicing the balancer, power must be disconnected by
removing the power cord from the electrical power outlet.
After servicing, be sure the balancer ON/OFF switch is in the "O" (off) position
before plugging the power cord into the electrical power outlet.
This device is rated as Class A for radiated emissions.
In the event of radio interference, the display read out may flicker - this is
®
normal.
Decal Information and Placement
Right Side View
Decal 128-1244-2 cautions the operator that spindle rotation may occur with
foot pedal depression and to keep clear of clamping components during
Quick-Thread
shaft rotation.
®
Decal 128-1785-2 warns the SmartWeight Pro
3R lasers and to avoid direct eye contact with the lasers. This decal is in
English and French languages.
Decal 128-1788-2 gives the maximum wheel diameter and maximum wheel
weight for the SmartWeight Pro
Decal 128-964-2 gives the maximum wheel diameter and maximumwheel
weight for the SmartWeight HN
Decal 128-1116-2 warns the operator not to view the laser light with optical
instruments for the SmartWeight HN
Decal 128-1117-2 shows the FDA performance standards compliance for the
SmartWeight HN
/ Elite
®
Decal 128-1610-2 cautions the operator that hood movement can create pinch
points.
Decal 128-1638-2 : EN/IEC Class 1 Laser Product Certification is shown on
Decal 128-1638-2. This label shows the EN/IEC standards for a Class 1 Laser
Product.
Decal 128-381-2: warns the operator not to remove the covered of the
SmartWeight Elite because of the risk of the electrical shock and not to use
below garage floor level.
Back View
Decal 128-381-2 (-08) warns the operator not to remove the cover of the
SmartWeight Pro
HN
® /
to use below garage floor level.
Decal 128-1155-2 states FDA standards for Class 2M laser compliance for the
HammerHead
TDC laser system.
®
Decal 24-198-2 displays model and electrical information for the SmartWeight
Pro
balancer.
®
Decal 128-1693-2 informs the operator that SmartWeight Pro
Standard 201.
Decal 128-907-2 not to use the SmartWeight Pro
Decal 128-975-2 shows EC declaration information regarding air pressure.
Decal 128-1120-2 shows ETL listing and cautions not to use below garage
floor level.
and SmartWeight HN
Balancers are
®
®
utilizes FDA-compliant, class
®
.
®
/ Elite
.
®
®
balancer.
®
balancer.
®
Image 1.
Image 2.
/ Elite
because of the risk of electrical shock and not
®
®
below garage floor level.
®
conforms to UL
®
7
Publicidad
