IPC MLC-C Manual De Instrucciones página 20

DESIGNATED USE
The appliance is designed exclusively for the cleaning of ma-
chinery, vehicles, buildings, utensils and in general surfaces
suitable for treatment with a high pressure jet of cleaning solu-
tion at between 25 and 250 bars (360-3600 PSI).
It has been designed for use with the detergents supplied or
recommended by the Manufacturer.
The use of other detergents or chemicals products may jeopar-
dise the safety of the appliance.
This appliance must be used exclusively for the purposes for
which it was designed.
All other uses are considered improper and unreasonable.
Examples of unreasonable use include:
- Washing surfaces not suitable for treatment with a high
pressure jet.
- Washing people, animals, electrical appliances and the
appliance itself.
- Use of unsuitable detergents or chemical products.
- Blocking the lance trigger in the delivery position.
- Installation on unsuitable walls.
Improper, incorrect or unreasonable use absolves the Manu-
facturer of all liability.
All high pressure washers are constructed in compliance with
current safety standards and regulations.
PRELIMINARY OPERATIONS
UNPACKING
After unpacking the high pressure washer, make sure it is intact
and undamaged.
If in doubt, do not use.
Contact your dealer.
Packaging elements (plastic bags, boxes, nails, etc.) must not
be left within reach of children as they are a potential source of
danger and must be disposed of or stored in compliance with
national environmental protection standards.
ASSEMBLING DISASSEMBLED PARTS OF THE MACHI-
NE.
The main parts of the machine and safety devices are assem-
bled by the Manufacturer.
To facilitate packing and transport, a number of secondary
components of the high pressure washer are supplied disas-
sembled.
The user is responsible for assembling these components ac-
cording to the instructions provided in each assembly kit.
RATING PLATE:
The rating plate with the principal technical characteristics
of your high pressure washer is located on the trolley and is
always visible.
English
Warning
!
On receipt of the product, make sure the rating plate is
present. Otherwise contact the Manufacturer and/or dealer
immediately.
Use of equipment without a rating plate absolves the Manu-
facturer of all liability. Products without a rating plate must
be considered anonymous and potentially dangerous.
WALL-MOUNTED INSTAL-
LATION.
The wall-mounted pressure
washer must always be in-
stalled on solid concrete or
masonry walls.
! Danger
Never install the wall-mounted
pressure washer on plaster-
board or hollow brick partition
walls.
To secure the appliance to the
wall, use suitable devices based on the tyre of construction of
the wall and the weight of the pressure washer being installed
(see the table of technical specifications).
Install the wall-mounted pressure washer at a height of at least 1
m above the ground, protected against dripping or water spray.
!
Danger
Never use the wall-mounted pressure washer if this is resting
horizontally on the ground or not secured to a wall.
COMMAND AND CONTROL DEVICES
Warning
!
Before connecting the high pressure washer to the mains elec-
tricity and water supplies, you should familiarise yourself with
the command and control devices.
To do this, follow the instructions in this manual and refer to
the relative figures.
CONNECTING TO THE MAINS WATER SUPPLY
Connect the water supply hose to the mains water supply (fig.
2A) and to the coupling on the high pressure washer (fig. 2B).
Check that the mains water supply provides a sufficient quantity
and pressure of water to ope-
rate the high pressure washer
200 - 800 kPa. (29 - 116 PSI).
Maximum inflow water tempe-
rature 50°C. (122°F).
ASSEMBLING THE ACCES-
SORIES
!
Warning
Risk of injury.
Use only original accessories
provided or authorised by the
Manufacturer.
- 20 -
FIG. 1
A A
B B
C C
FIG. 2