Descargar Imprimir esta página

Black and Decker BCRT8K Manual De Instrucciones página 9

Publicidad

Idiomas disponibles

Idiomas disponibles

ANSI Z87.1 eye protection (CAN/CSA Z94.3),
ANSI S12.6 (S3.19) hearing protection,
NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction activities
contains chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
lead from lead-based paints,
crystalline silica from bricks and cement and other
masonry products, and
arsenic and chromium from
chemically-treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter
out microscopic particles.
Wear protective clothing and wash exposed areas
with soap and water. Allowing dust to get into your
mouth, eyes, or lay on the skin may promote absorption of
harmful chemicals. Direct particles away from face and body.
Use the appropriate dust extractor vacuum to remove
the vast majority of static and airborne dust. Failure
to remove static and airborne dust could contaminate the
working environment or pose an increased health risk to
the operator and those in close proximity.
Use clamps or other practical ways to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and may
lead to loss of control and injury.
Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be caught
in moving parts.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
BPM .................... beats per minute
V ......................... volts
min ..................... minutes
or DC ......... direct current
.../min .............. per minute
RPM .................... revolutions per
minute
A ......................... amperes
Hz ....................... hertz
W ........................ watts
Wh ...................... watt hours
n o ....................... no load speed
n ......................... rated speed
.................... safety alert symbol
BATTERY AND CHARGER
The battery is not fully charged out of the carton. Before using
the charger to charge the battery, read the safety instructions
below and then follow charging procedures outlined.
.................... wear respiratory
protection
.................... wear eye protection
.................... Class II Construction
(double insulated)
.................... wear hearing
protection
.................... read all
documentation
.................... avoid staring at
light
or AC .......... alternating current
Ah ....................... amp hours
Charging Procedure (Fig. A, B)
WARNING: Do not use tool while it is connected to the
USB cable.
1. Pull the micro USB charging port cover 
the tool.
2. Insert the micro USB plug 
3. Plug the USB plug 
into any USB port (such as on a
 13
computer). The green charging LED 
blink while charging.
4. Ensure the green charging LED 
green charging LED is not illuminated, adjust tool handle
to ensure charging contacts are touching.
5. Charging is complete when the five green charging
LEDs 
remains continuously ON. Battery can be left
 4
charging or USB cable can be disconnnected.
6. Let the tool charge initially for at least 1 hour. After the
initial charge, your tool should be fully charged in 1 hour
from a fully discharged condition. Recharge discharged
batteries as soon as possible after use or battery life may
be greatly diminished. For longest battery life, do not
discharge batteries fully. It is recommended that the
batteries be recharged after each use.
Hot/Cold Delay
When the tool detects that the battery that is too hot or too
cold, it automatically starts a hot/cold delay, suspending
charging until the battery has reached an appropriate
temperature. The tool then automatically switches to
charging mode. This feature ensures maximum battery life.
1. A cold battery may charge at a slower rate than a
warm battery.
2. The hot/cold delay will be indicated by the orange
charging LED 
 4
remaining OFF.
3. Once the battery has reached an appropriate
temperature, the green charging LED 
illuminate, indicating that the tool has resumed the
charging procedure.
Electronic Protection System
Li-Ion tools are designed with an Electronic Protection
System that will protect the battery against overloading,
overheating or deep discharge. The tool will automatically
turn off and the battery will need to be recharged.
Important Charging Notes
1. The tool may become warm to the touch while charging.
This is a normal condition, and does not indicate a
problem. To facilitate the cooling of the tool after use,
avoid placing the tool in a warm environment such as in
a metal shed or an uninsulated trailer.
2. If the tool does not charge properly, take the tool and
charger to your local service center.
3. You may charge a partially used battery whenever you
desire with no adverse effect on the tool.
READ ALL INSTRUCTIONS
ENGLISH
away from
 14
 12
into the charging port 
 10 
 4
will continuously
 4
is illuminated. If the
 4
will continuously
.
7

Publicidad

loading