Hendi 274125 Manual Del Usuario página 17

• Pull out the rod (G) and spring (H) from the tap body (the
pin/gasket assembly (I) will slide out together with the rod).
(Fig.27 on page 8).
• Detach the rod (G) from the pin/gasket assembly (I). (Fig.28
on page 8).
• Disassemble (by pulling) the pin (L) from the gasket (M).
(Fig.29 on page 8).
7. Washing and sanitizing the components
All of the component parts previously disassembled (tap, mixer,
mixing auger, gasket and bowl) must be carefully washed and
sanitized.
To carry out this procedure correctly proceed as follows:
• Fill a container with detergent and hot water with a tempera-
ture of 50~60°C (122~140°F);
• Wash the disassembled components with the detergent solu-
tion;
• Rinse with hot water;
• Clean only with warm water and a sanitizing product made
from sodium hypochlorite diluted in water to obtain an active
chloride concentration of 0.02%;
• Immerse the disassembled component parts in the sanitizing
solution for about 30 minutes;
• Rinse with clean water;
• Clean the bowl lid,(see section 11).
• Place the components on a clean surface and dry them.
8. Assembling the washed components
All washed and sanitized component parts must be re-assem-
bled with care and then subsequently refitted to the machine,
following the relevant steps.
8.1. Assembling the bowl
WARNING! Make sure that the gasket is correctly assembled.
• A seal correctly assembled; here the seal perfectly adheres to
the bowl edge. (Fig.30 on page 8).
• A seal which is not correctly assembled; here the seal does
not perfectly adhere to the bowl edge. (Fig.31 on page 8).
• Fit the bowl back into place firmly downward, after moisten-
ing the seal with water. (Fig.32 on page 8).
DO NOT USE GREASE OR VASELINE.
WARNING! Make sure that the bowl is correctly fitted to the
machine; an incorrectly fitted bowl will cause the product to
leak out; risk of scalding!
• A bowl correctly assembled; here the bowl perfectly adhere to
the machine edge. (Fig.33 on page 9).
• A bowl which is not correctly assembled; here the bowl does
not perfectly adhere to the machine edge. (Fig.34 on page 9).
• Fix the bowl to the machine body using the relevant hook-on
handles. (Fig.35 on page 9).
• Insert the mixer auger into its seating. (Fig.36 on page 9).
• Insert the mixer into its seating following the steps described
in section 3 in inverse order. (Fig.37 on page 9).
8.2. Assembling the tap
(Fig.38 on page 9)
• To assemble the tap, carry out in reverse all of the disassem-
bly steps illustrated previously.
• To fit the level (F) push the rod (D) from the inside until the
guides protrude; the insert the level (F) and slowly release the
rod (D).
8.3. Fitting the tap
(Fig.39 on page 10)
To fit the lap correctly back in place proceed as follows:
• Hold down the button, making sure that the road is complete-
ly extracted;
• Introduce the tap into the seat provide and push until the
pushbutton returns to its initial position.
9. Internal sanitization
WARNING! The temperature regulator must be set to -OFF-
Carry out the following steps:
• Prepare the sanitizing solution (see section 7)
• Fill the bowl with the sanitizing solution;
• Leave the solution to act for about 30 mins;
• Empty out the sanitizing solution from the bowl;
Then rinse out the bowl and inside surfaces thoroughly to elim-
inate all residues of sanitizing solution.
10. Cleaning the drip tray
(Fig.40 on page 10)
The drip tray should be emptied and cleaned daily.
Note: the tray needs to be emptied out and cleaned every time
that the red float fitted to the grid rises, this is to stop liquid
from leaking out.
Lift the tray with grid and pull it outwards to remove it from
its seating.
• Wash the tray and grid separately with lukewarm, water;
• Dry all of the component
• Reposition the grid on top of the tray;
• Fit the tray back in place and press down to secure it to the
machine.
11. Cleaning the bowl lid
(Fig.41 on page 10)
• Remove the bowl lid from the machine;
• Clean the surface using a damp cloth and / or a non-abrasive
sponge soaked in sanitizing product.
• Rinse thoroughly using clean water.
12. Emptying the water boiler tank
WARNING! While the water boiler tank is being emptied, the
machine must be unplugged.
WARNING! The boiler may be emptied only when the bowl is
empty and the machine has cooled down sufficiently.
The use of water from the boiler tank for food purposes is
empty prohibited.
(Fig.42 on page 10)
To empty the boiler proceed as follows:
• Unplug the machine.
• Remove the drip tray, as described in the relevant section 8.
• Remove the lid for water boiler.
(Fig.43 on page 10)
• Place the machine on a flat surface and with the boiler tank
tumed towards to the outer edge of the support surface.
• Place a container (B) with a capacity of more than 3 litres
undemeath the bleeder cap (X);
• Use a coin or Allen wrench to unscrew the bleeder cap (X).
Alternatively, you can use water boiler's lid to unscrew it.
(Fig.44 on page 10)
• Pull out the bleeder cap (X) with a firm movement and wait for
all the water to empty out from the boiler tank.
GB
17