Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
USING THE 60HZ FILTER
The Digital Probe-Pro has a 60Hz filter to help trace cables/wires when toning
The Digital Probe-Pro has a 60Hz filter to help trace cables/wires when toning
The Digital Probe-Pro has a 60Hz filter to help trace cables/wires when toning
near devices running on 60Hz. Press the Analog Toning Mode / 60Hz Filter
near devices running on 60Hz. Press the Analog Toning Mode / 60Hz Filter
On/Off Button
P12 P12 P12
illuminate when the 60Hz filter is on.
illuminate when the 60Hz filter is on.
illuminate when the 60Hz filter is on.
illuminate when the 60Hz filter is on.
NOTE: 60Hz filtering can only be used with analog toning.
FIG. 2
2"
(51 mm)
RJ11 / RJ12 / RJ45 TESTING
The Digital Toner-Pro has an RJ45 Test Port
the ABN clips to transmit the tone. The RJ45 plug works with RJ11, RJ12,
the ABN clips to transmit the tone. The RJ45 plug works with RJ11, RJ12,
the ABN clips to transmit the tone. The RJ45 plug works with RJ11, RJ12,
or RJ45 jacks. The red
the two center conductors of the inserted plug, i.e. pins 2 and 3 for RJ11,
pins 3 and 4 for RJ12, and pins 4 and 5 for RJ45.
Use the Digital Probe-Pro to locate the toned wires at the far end of the cable,
as described in the TRACING PAIRED WIRES section.
CONTINUITY TEST (ANALOG TONING ONLY)
The Digital Toner-Pro transmits frequencies on non-energized wires only. When
the Digital Toner-Pro is turned on, a continuity test will be performed to determine
if the 2 wires to be traced are in close proximity to each other, without a conductive
if the 2 wires to be traced are in close proximity to each other, without a conductive
path between them. The "CONT" Indicator
pass. Attach the red and black ABN Test Clips
If the resistance of the circuit is less than 10k , the "CONT" Indicator
illuminate red, indicating a short, and no toning can occur. If the "CONT" Indicator
is illuminated green, a tone can be generated and testing can proceed.
POLARITY AND VOLTAGE PRESENCE TESTING
The Digital Toner-Pro may be used to test the polarity and type of voltage
present.
1. If testing via the RJ45 PORT
ABN Test Leads, connect the Digital Toner-Pro's red
ABN Test Leads, connect the Digital Toner-Pro's red
Test Clip leads to their respective Test Lead Inputs
2. Connect the ABN Test Clips, or insert a cable into the RJ45 PORT
3. Turn Digital Toner-Pro on by pressing the Power On/Off button
4. Select Test Mode by pressing the Mode Button
Select Test Mode by pressing the Mode Button
Test Mode Indicator
8
OPERATING INSTRUCTIONS
to turn the 60Hz filter on/off. The Filter Indicator
to turn the 60Hz filter on/off. The Filter Indicator
and black
T14 T14
, proceed directly to step 2. If testing via the
, proceed directly to step 2. If testing via the
, proceed directly to step 2. If testing via the
T21 T21 T21
is illuminated.
is illuminated.
T1 T1
that can be used in place of
that can be used in place of
T21 T21 T21
ABN Test Clip leads are replaced by
ABN Test Clip leads
T15 T15
wIll illuminate green to indicate
wIll illuminate green to indicate
wIll illuminate green to indicate
wIll illuminate green to indicate
T4 T4
,
to the wires to be tested.
to the wires to be tested.
T14 T14 T14 T14 T14
T15 T15
T14 T14
T20 T20 T20
T8 T8
P13 P13
will
will
T4 T4
and black
T15 T15
.
.
T21 T21 T21
.
T9
repeatedly
repeatedly until the
repeatedly until the
repeatedly
will
will
ABN
ABN
Publicidad
