TOPRO Taurus E Basic Instrucciones De Uso página 61

Guidance and manufacturer's declaration
Electromagnetic IMMUNITY for ME EQUIPMENT and ME SYSTEMS that are not LIFE-SUPPORTING
The TOPRO Taurus is intended for use in the electromagnetic environment specifi ed below.
The customer or the user of the TOPRO Taurus should assure that it is used in such an environment.
IMMUNITY test IEC 60601 TEST LEVEL
Conducted RF 3 Vrms
IEC 61000-4-6 150 kHz to 80 MHz
Radiated RF 3 V/m
IEC 61000-4-3 80 MHz to 2,5 GHz
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is aff ected by absorption
and refl ection from structures, objects and people.
a) Field strengths from fi xed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios,
amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the
electromagnetic environment due to fi xed RF transmitters, an electromagnetic site survey should be considered. If the measured
fi eld strength in the location in which the TOPRO Taurus is used exceeds the applicable RF compliance level above, the
TOPRO Taurus should be observed to verify normal operation. If abnormal performance is observed, additional measures may
be necessary, such as re-orienting or relocating the TOPRO Taurus.
b) Over the frequency range 150 kHz to 80 MHz, fi eld strengths should be less than 3 V/m.
Recommended separation distances between portable and mobile RF communications equipment and
the ME EQUIPMENT or ME SYSTEM for ME EQUIPMENT and ME SYSTEMS that are not LIFE-SUPPORTING
The TOPRO Taurus is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
The customer or the user of the TOPRO Taurus can help prevent electromagnetic interference by maintaining a minimum distance
between portable and mobile RF communications equipment (transmitters) and the TOPRO Taurus as recommended
below, according to the maximum output power of the communications equipment.
Rated maximum output power
of transmitter W
0,01
0,1
1
10
100
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters (m) can be
estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the
transmitter in watts (W) according to the transmitter manufacturer.
NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is aff ected by absorption and refl ection
from structures, objects and people.
Compliance level Electromagnetic environment – guidance
3 V Portable and mobile RF communications equipment should
be used no closer to any part of the TOPRO Taurus, including
cables, than the recommended separation distance calculated
from the equation applicable to the frequency of the transmit-
ter.
Recommended separation distance
d=1,16√P
d=1,16√P 80 MHz – 800 MHz
d=2,33√P 800 MHz – 2,5 GHz
3 V/m where P is the maximum output power rating of the transmitter
in watts (W) according to the transmitter manufacturer and d
is the recommended separation distance in metres (m). Field
strengths from fi xed RF transmitters, as determined by an elec-
tromagnetic site survey a), should be less than the compliance
level in each frequency range b).
Interference may occur in the vicinity of equipment
marked with the following symbol:
Separation distance according to frequency of transmitter m
150 kHz–80 MHz 80 MHz–800 MHz
d=1,16√P
0,12
0,37
1,16
3,67
11,6
– 57 –
TOPRO Taurus E
800 MHz–2,5 GHz
d=1,16√P
0,12
0,37
1,16
3,67
11,6
Art. No. User Manual: 104801 – Revision C, 2022-05
EN EN
NO
DE
NL
SV
DA
FI
IS
FR
IT
ES
CS
d=2,33√P
0,23
0,74
2,33
7,37
23,3