must be cleaned of residual medication and
contamination.
• To do this, dismantle the atomiser
masks
and the nasal douche [n/a] into
13 14
their individual parts.
• Remove the mouthpiece
or the nosepiece [n/a] from the atomiser.
• Disassemble the nosepiece [n/a] if you have
used it with the comfort attachment.
• Dismantle the atomiser by twisting the top
section anticlockwise against the medication
container
.
11
• Remove the atomiser insert
medication container
• Remove the valve
atomiser
.
8
• Reassembly is carried out in reverse order.
Cleaning
Important
The device must be switched off, disconnected
from the mains and allowed to cool down each
time before cleaning.
The atomiser and the used atomiser set, such as
the mouthpiece
, mask
12
nasal douche etc. must be washed with hot but
not boiling water after each use. Dry the parts
carefully using a soft cloth. Put the parts together
again when they are completely dry and place
them in a dry, sealed container or disinfect them.
When cleaning, ensure that any residue is
removed. Never use any substances for cleaning
that could potentially be toxic if they came into
contact with the skin or mucous membranes, or if
they were swallowed or inhaled.
Use a soft, dry cloth and non-abrasive cleaning
products to clean the device.
Do not use any abrasive cleaning products and
never submerge the device in water.
Important
• Ensure that no water gets inside the device.
• Do not clean the device or replacement set in
the dishwasher.
• Do not touch the device with wet hands when
it is plugged in and do not allow water to
spray on the device.
• Only operate the device if it is completely dry.
• Do not spray any liquid into the vents! If
liquid penetrates the device this could cause
, the
8
, the mask
12
13 14
from the
9
.
11
by pulling it out of the
10
, atomiser
13 14
damage to the electrics or other nebuliser
parts and lead to a malfunction.
Condensation, hose care
Condensation may form in the hose depending on
the ambient conditions. It is essential to remove
the moisture to prevent bacterial growth and
ensure proper treatment. To do so, proceed as
follows:
• Disconnect the compressed air hose
the atomiser
• The hose must remain in the nebuliser
• Operate the nebuliser until the moisture is
removed by the air passing through.
• In the event of heavy contamination, replace
the hose.
Disinfection
Please carefully observe the points below when
disinfecting your atomiser and atomiser set. We
recommend disinfecting the individual parts on
a daily basis after the last usage as a minimum
measure.
(A small amount of clear vinegar
and distilled water can be used.)
• First, clean the atomiser and atomiser set as
,
8
described in the "Cleaning" section.
• Place the disassembled atomiser
nasal douche [n/a], the mouthpiece
silicone masks
nosepiece [n/a] in boiling water for 5 minutes.
• For the remaining atomiser set parts, use a
vinegar solution consisting of ¼ vinegar and
¾ distilled water. Make sure that the volume is
sufficient to fully submerse parts, such as the
PVC masks [n/a] and hose
Atomiser set parts that can be boiled can also
be disinfected in this way.
• Leave the parts in the vinegar solution for
30 minutes.
• Rinse the parts with water and dry them
carefully with a soft cloth.
Important
Do not boil or autoclave the compressed air hose
and the PVC masks [n/a].
• Put the parts together again when they are
completely dry and place them in a dry,
sealed container.
Note
Please ensure that the parts are completely dried
after cleaning, otherwise the risk of bacterial
growth is increased.
23
.
8
8
and the disassembled
13 14
, in the solution.
7
from
7
.
4
and
, the
12