Descargar Imprimir esta página

Skil 1415 Manual Original página 12

Ocultar thumbs Ver también para 1415:

Publicidad

• Holding and guiding the tool 0
- pencil grip for precision work (engraving)
- one-hand grip for less precise work (grinding)
- support grip for additional control/comfort
- do not apply too much pressure on the tool; let the
speed do the work for you
• Support grip !
- can be adjusted as illustrated
- can be mounted in 4 diferent positions
• Spot light (not standard included) @
Switch on/of spotlight J by turning knob K counter-
clockwise/clockwise
• Flexible shaft (not standard included) #
- mount lexible shaft as illustrated
- use lexible shaft for hard-to-reach places
Changing accessories when using lexible shaft $
- pull sleeve L down (= lock spindle) and hold it while you
turn collet nut D by hand until the spindle lock prevents
further rotation and loosen collet nut D with wrench E
- insert an accessory in collet C
- pull sleeve L down (= lock spindle) and hold it while
you tighten collet nut D with wrench E
• Mounting stand (not standard included) %
- mount stand on a workbench or table-top with a
maximum thickness of 60 mm
- adjust height of stand by turning tubes M counter-
clockwise, pulling them to desired height, and turning
them clockwise
- adjust height of suspension bracket N by loosening
knob P, adjusting suspension bracket to desired
height, and tightening knob P
- attach tool to suspension bracket with hook Q
• Assembly of speciic accessories ^
MAINTENANCE / SERVICE
• Always keep tool and cord clean (especially ventilation
slots H 2)
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in manu-
facturing and testing procedures, repair should be carried
out by an after-sales service centre for SKIL power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skileurope.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol & will remind you of this when the need for
disposing occurs
DECLARATION OF CONFORMITY
• We declare under our sole responsibility that this product
is in conformity with the following standards or
standardized documents: EN 60745, EN 55014,
EN 61000 in accordance with the provisions of the
directives 2006/95/EC, 2004/108/EC, 2006/42/EC
• Technical file at: SKIL Europe BV (PT-SEU/PJE),
4825 BD Breda, NL
08.12.2011
NOISE/VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 72 dB(A) (standard deviation:
3 dB) and the vibration 2.9 m/s² (hand-arm method;
uncertainty K = 1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for diferent applications, or with diferent
or poorly maintainted accessories, may signiicantly
increase the exposure level
- the times when the tool is switched of or when it is
running but not actually doing the job, may signiicantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
Outil rotatif à grande vitesse
INTRODUCTION
• Cet outil est conçu pour le meulage, ponçage,
tronçonnage, gravure, polissage et perçage de haute
précision des diférents matériaux
• SKIL ne fournit pas d'accessoires de rechange pour cet
outil, mais recommande l'achat d'accessoires Ø 2,4 mm/
Ø 3,2 mm DREMEL
• Lisez et conservez ce manuel d'instruction 3
SPECIFICATIONS TECHNIQUES 1
ELEMENTS DE L'OUTIL 2
A Interrupteur marche/arrêt
B Bouton de blocage de l'arbre
C Pince
D Chapeau
11
1415

Publicidad

loading

Este manual también es adecuado para:

F0151415