Maglite ML150LR7 Manual Del Propietário página 13

Troubleshooting
Section 6
If you have questions or need assistance, please call our warranty/repair
facility at 01 (909) 947-1006.
Problem Cause/Correction
Flashlight: 1. Make sure battery is installed, with positive (+) end toward head of
Does not light flashlight.
2. Make sure large end of battery spring is snapped into tailcap.
3. Tighten tail cap – make sure unplated area of tail cap and barrel are
clean. See fig. 12
Battery charged? 1. Check battery charge: Place flashlight in recharger/cradle. Make
sure LED lights up (see page 8). Charge for 15 minutes ... check
for light. If it lights (even momentarily) charge it, if not, replace it
(battery).
Switch sticks 1. Return flashlight to Mag Instrument (see warranty).
1. Check for damage to battery casing.
Works intermittently
2. Foreign particles inside barrel.
Poor or no spot 1. Damaged LED.
Recharger/Cradle:
1. Tighten tail cap.
LED indicator does
2. Check plug connection to
not light.
converter.
3. Check plug to power
source.
4. Make sure large end of
battery spring is
snapped into tailcap.
Inspection and Maintenance
Battery Pack – See Warnings Section for more information. Periodically (approximately
every month) remove the battery pack from the flashlight and visually inspect for signs
of gas or chemical leakage. Indications of leakage are discoloration of the plastic sleeve
or white fuzzy material near the top (positive button) of each cell. Another indication
would be a bulging deformation of the bottom (negative flat end) of the cell can. If
these signs are observed the battery pack should be removed from service to prevent
chemical damage to the inside of the flashlight. See One Year Battery Pack Warranty
for more information concerning warranty coverage.
Fully Charged Battery Storage – If you do not use your flashlight for long periods of
time (four months or more) we suggest you remove the battery pack from the flashlight
to prevent chemical damage (acid leaks). Electrical Contacts – The bare (bright) metal
12
Specifications and Accessories
Flashlight
• Tempered aluminum alloy body
• Finish: hard, type III, aircraft anodized
(inside and out)
• Length: ML150LR™-10-11/16"
(271.45 mm) / ML150LRS™-8-1/4"
(210 mm)
• Weight, with battery pack:
ML150LR™-15.5 oz. (439 grams) /
ML150LRS™-11.2 oz. (317.51 grams)
• Head diameter: 1-15/16" (49.12 mm)
• Barrel diameter: 1-3/16" (30.15 mm)
• Permanently engraved serial number
for registration and identification
surfaces between the tailcap and barrel must be cleaned periodically to ensure a
good electrical contact. Also keep the tailcap spring clean. O-ring Seals and Screw
Threads – To keep seals from drying out and the threads operating smoothly, apply
Fig. 12
several drops of clean petroleum oil or jelly to these surfaces two or three times a
year. Anodized Exterior Finish – The protective finish on the flashlight is very durable;
however, constant exposure to sunlight, water, chemicals, gases, etc., will dull, discolor
and eventually destroy the protective finish. Care should be taken to avoid any harsh
environment.
12 Volt Adapter (Automobile)
Unplated Area
Plug the DC power cord's adapter into the 12–14
volt cigarette lighter receptacle of the vehicle.
DO NOT leave adapter plugged in for any
extended period while the engine is "off"
to avoid draining vehicle battery.
m
WARNING:
systems only. Do not use it to connect to a 24 volt circuit,
as doing so can create excessive heat, possibly cause a fire,
and damage electrical components.
120-240 Volt Converter (Indoor)
After mounting the charging cradle in a
proper location, plug the converter into an
appropriate 120-240 volt wall receptacle.
Note: Total usable wire length is 6 feet.
• O-ring sealed throughout
• 6.4V-ML150LR™ / 3.2V-ML150LRS™
lithium iron phosphate (LiFePO 4 )
rechargeable battery pack
• Polycarbonate Lens
• Micro-polished reflector
• Diamond knurl design
• Adjustable beam from spot to flood
with about 1/4 turn of head
• Corrosion resistant metal
springs throughout
Charging Cradle
• Accepts 12–14 volts DC (not for use
with 24-volt systems)
This adapter is designed for 12-14 volt
• Solid-state charging circuit
• Charge rate: 2500 mA
• Reverse voltage protected (prevents
damage if battery is inserted
backwards)
• Multi-color LED charge indicator
Converter
• 120-240 volts AC 50/60Hz
• Output 12 volts DC
• Double insulated