Roadstar HIF-8888TUMPN Manual De Instrucciones página 6

2. Press again " FIND " button, the folder name is being displayed. then press the "skip
up" (or skip down) button to select the desired folder, and press the cd" PLAY/PAUSE/
STOP " button (2) to start the playback of all tracks inside that selected folder.
REMARK:
- In that case of no name had been assigned for the track, " none " or " unknown " is being
displayed" on display (18).
- The LCD display support english language only.
MP3/WMATRACK FORMAT REQUIREMENT:
- MP3 bit rate : 32 kbps~256 kbps and wma bit rate : 32 kbps ~ 320 kbps
- The performance of playing MP3 disc is various from the quality of recording disc and
the method of recording. Furthermore, the searching lead-time for MP3-CD is longer
than normal cd due to difference format.
REPEAT/INTRO/RANDOMMODE
Press the repeat/intro/random button before or during playback, a single track, single
folder (MP3 only) or all the tracks can be played in difference mode as follow:
FOR CD
(1) REPEAT 1 (2) REPEAT ALL TRACK
(5) OFF MODE
INDICATOR
PLAY MODE ON LCD DISPLAY
REPEAT TRACK
REPEAT ALL ALL
INTRO INTRO
RANDOM RANDOM
OFF MODE ------------
FOR MP3/WMA DISC
(1) REPEAT 1 (2) REPEAT 1 FOLDER
(6) OFF MODE (5) RANDOM
INDICATOR
PLAY MODE ON LCD DISPLAY
REPEAT SINGLE TRACK
REPEAT ALL TRACKS
REPEAT SINGLE FOLDER
INTRO PLAY MODE INTRO
RANDOM MODE RANDOM
OFF MODE -------------
English
(3) INTRO (4) RANDOM
(3) REPEAT ALL FOLDER
(4) INTRO PLAY
ALL
English
7 8
Repeat play
You can listen the desired tracks or folder repeatedly by this function.
Intro play (by remote control)
You can listen the beginning (10 seconds) of each track in a cd by this function & saving
your time to search the desire song
Random play
You can listen all the tracks or folder in a random order by this function
CD DISC PROGRAMMING (BY REMOTE CONTROL)
Up to 32 tacks can be programmed for CD or MP3 file and play in any order. before use, be
sure the system is at stop mode before programming:
1. Set in CD/USB mode & stop the cd playback.
2. Press the "PROGRAM" button, " PROG " will appear on LCD display (18). Moreover, it
will indicate program no. and digits for track no. to be programmed.
3. Select a desired track by pressing SKIP
4. Press the " program " button to store the trace into memory.
5. Repeat steps 3 and 4 to enter additional tracks into the memory if necessary.
6. When all the desired tracks have been programmed, press cd " PLAY/PAUSE/STOP "
button (2) to play the disc in assigned order. .
7. To cancel the programmed file, press "STOP" button on remote handset until " PROG
" is disappear on LCD display (18)
PLAYBACK OF MP3/WMA SONG VIA USB STORAGE MEDIA OR MEMORY
CARD CONNECTING
The system is able to decode and playback all MP3 /WMA file which stored in the memory
media with USB connecting port or SD/MMC memory card.
1.
Set function selector (15) at CD/USB mode and then press SOURCE button (6) to
select " USB or CARD" mode.
2. Plug-in the USB plug with the face up & make sure it going into completely or insert
the memory card in the direction of the arrow as shown in the label on the underside
of the MEMORY CARD slot cover. Insert straight without bending.
Connecting the USB upside down or backwards could damage the audio system or
the storage media (usb thumb drive / sd/mmc card). Check to be sure the direction is
correct before connection.
3. The system will start reading the storage media automatically after connecting, and
LCD display (18) will show the total number of MP3/WMA files and total number of
folder being detected.
4. Repeat the same playback procedure as playing CD/MP3 disc as above.
or buttons (3).